Siemens fault codes

Fault codes

• 000 Alarm diagnostics not possible
• 001 Drive has no firmware
• 002 Computation time overflow
• 003 Watchdog triggered NMI
• 004 Stack overflow
• 005 Invalid opcode/Trace/SWI/NMI (DSP)
• 006 Checksum test error
• 007 Error when initializing
• 020 Cycle fault triggered NMI
• 025 SSI interrupt
• 026 SCI interrupt
• 027 HOST interrupt
• 028 Actual current sensing during power-up
• 029 Incorrect measuring circuit evaluation
• 030 S7 communication error
• 031 Internal data error
• 032 Incorrect number of current setpoint filters
• 033 Incorrect number of speed setpoint filters
• 034 Axis count function failure
• 035 Error when saving the user data
• 036 Error when downloading the firmware
• 037 Error when initializing the user data
• 039 Error during power section identification. Supplementary info
• 040 Required option module is missing
• 041 Firmware does not support this option module
• 042 Internal software error
• 043 Firmware and option module mismatch
• 044 Connection to option module failed
• 048 Illegal status PROFIBUS hardware
• 101 Program block %n target position exceeds the forward software limit
• 102 Program block %n target position exceeds the reverse software limit
• 103 Block number %n
• 104 Block %n
• 106 Block %n
• 107 Block %n
• 108 Block number %n available twice
• 109 Program block %n: External program block change was not requested
• 110 Selected block number %n does not exist
• 111 GOTO in block number %n not permissible
• 112 Run task and reference point return/handwheel are active simultaneously
• 113 Run task and jog/handwheel activated simultaneously
• 114 Program block %n must be program block change enable END
• 115 Traversing range start reached
• 116 Traversing range end reached
• 117 Program block %n: Target position is below the start of the travel range
• 118 Program block %n: Target position exceeded the end of the travel range
• 119 PLUS software limit switch actuated
• 120 MINUS software limit switch actuated
• 121 Jog 1, jog 2, or handwheel valid simultaneously
• 122 Parameter %u
• 123 Linear encoder invalid for the selected unit of measurement
• 124 Referencing and jog simultaneously started
• 125 Falling edge of reference cam not detected
• 126 Block %n
• 127 Block %n
• 128 Block %n
• 129 Maximum speed too high for a rotary axis with modulo conversion
• 130 Controller or pulse enable withdrawn in motion
• 131 Following error too high
• 132 Drive is beyond the negative software limit
• 133 Drive is beyond the positive software limit
• 134 Positioning monitoring triggered
• 136 Parameter set %d: Speed feedforward conversion factor cannot be represented
• 137 Parameter set %d: Position controller output conversion factor cannot be represented
• 138 Conversion factor between motor and load too large
• 140 Minus hardware limit switch
• 141 Plus hardware limit switch
• 142 Input I0.x not set as equivalent zero pulse
• 143 Continuous travel and external program block change in program block %n
• 144 Switching-in/switching-out MDI erroneous
• 145 Fixed endstop not reached
• 146 Fixed stop: Axis exceeded the monitoring window
• 147 Enable signals withdrawn at the fixed endstop
• 148 Velocity in block %n outside the range
• 150 External position reference exceeded the maximum travel range
• 151 External position reference exceeded the minimum travel range
• 160 Reference cam not reached
• 161 Reference cams too short
• 162 No zero reference pulse present
• 163 Encoderless operation and operating mode mismatch
• 164 Coupling released during the traversing job
• 165 Absolute positioning block not possible
• 166 Coupling not possible
• 167 Activate coupling signal present
• 168 Buffer overflow
• 169 Coupling trigger missed
• 170 Coupling switched-out during the traversing program
• 171 Coupling not possible
• 172 External block change for coupling not possible
• 173 Coupling and traverse to endstop simultaneously
• 174 Passive referencing not possible
• 175 Passive referencing not realized
• 176 Absolute encoder must be adjusted
• 177 Start-up passive referencing P179 not possible
• 180 Teach-in without reference point
• 181 Teach-in block invalid
• 182 Teach-in standard block invalid
• 183 Teach-in block not found
• 184 Teach-in standard block not found
• 185 Positioning mode invalid
• 186 Spindle cannot perform homing
• 188 Spindle positioning
• 189 Incremental jogging is invalid
• 190 Actual firmware does not support spindle positioning
• 191 Zero mark setting unsuccessful
• 192 Max. search velocity too high
• 193 Zero mark not found
• 194 Spindle positioning is only available for motor 1
• 195 Speed pre-control not permissible
• 196 Illegal combination of input signals (warning %u)
• 300000 Hardware drive bus
• 300002 Axis %1 drive number %2 assigned twice
• 300003 Incorrect module type %3
• 300004 Incorrect drive type %3 (FDD/MSD)
• 300005 Unconfigured modules on the drive bus
• 300006 Module with drive number %1 not found on the drive bus
• 300008 Measuring circuit %3 unavailable
• 300009 Incorrect type for measuring circuit %3
• 300010 Drive activated but axis NC not assigned
• 300011 Spindle hardware version not supported
• 300012 Control module hardware version not supported
• 300020 Drive %1 removed for diagnostics
• 300101 Bus communications failure
• 300201 Access timeout
• 300401 Drive software for type %1 missing or incorrect
• 300403 Version mismatch between drive software and drive machine data
• 300404 Drive number mismatch in drive machine data
• 300405 Unknown drive alarm
• 300406 Acyclic communication fault
• 300410 File storage error
• 300411 File read error
• 300412 File storage error
• 300413 File read error
• 300423 Measuring results could not be read (%1)
• 300501 maximum current monitoring
• 300502 Maximum phase R current monitoring
• 300503 Maximum phase S current monitoring
• 300504 Motor measuring system measuring circuit error
• 300507 Rotor position synchronization error
• 300508 Motor measuring system zero pulse monitoring
• 300510 Actual current measurement zero point balancing error
• 300511 measuring function active
• 300512 direct feedback recognized
• 300513 Ground fault detected
• 300515 Power unit heatsink temperature out of range
• 300603 DC link voltage too high
• 300604 Motor encoder not calibrated
• 300605 Motor changeover invalid
• 300606 Flux controller at limit
• 300607 Current controller at limit
• 300609 Encoder cutoff frequency exceeded
• 300610 Rotor position identification failure
• 300611 generator mode
• 300612 Invalid current during rotor position identification
• 300701 start-up required
• 300702 Invalid basic cycle time
• 300703 Invalid current control cycle
• 300704 Invalid speed control cycle
• 300705 Invalid position control cycle
• 300706 Invalid monitoring cycle
• 300707 Basic cycle mismatch between axes
• 300708 Current control cycle mismatch between axes
• 300709 Speed control cycles differ between axes
• 300710 Position control cycle mismatch between axes
• 300711 Monitoring cycles differ between axes
• 300712 Cannot configure the high-dynamic controller structure
• 300713 Position controller advance time invalid
• 300714 Power unit code invalid
• 300715 Power unit maximum current less than or equal to zero
• 300716 Torque constant less than or equal to zero
• 300717 Motor moment of inertia is less than or equal to zero
• 300718 Calculated current controller dead time less than or equal to zero
• 300719 Motor not configured for delta-connected operation
• 300720 Invalid maximum motor speed
• 300721 No-load current exceeds rated motor current
• 300722 Motor no-load current greater than power unit rated current
• 300723 STS configuration of axes differ
• 300724 Number of pole pairs invalid
• 300725 Invalid measuring system encoder line count
• 300726 Voltage constant is zero
• 300727 Reactance is less than or equal to zero
• 300728 Torque/current adaptation factor too high
• 300729 Motor zero-speed current less than or equal to zero
• 300730 rotor resistance invalid
• 300731 Rated power less than or equal to zero
• 300732 Rated speed less than or equal to zero
• 300734 No-load current is less than or equal to zero
• 300735 Invalid field-weakening speed
• 300736 Lh characteristic invalid
• 300737 Cannot configure two EnDat encoders
• 300738 Measuring system module number unavailable
• 300739 Measuring system already used as the motor measuring system
• 300740 Measuring system used multiple times
• 300741 asynchronous mode
• 300742 voltage/frequency mode
• 300745 Safe end position limits interchanged
• 300746 SBH/SG not enabled
• 300747 Monitoring cycle MD1300 invalid
• 300748 Monitoring cycles of the two axes differ
• 300750 Incorrect speed control adaptive parameter settings
• 300751 Speed control gain too high
• 300752 Current setpoint filter stopband frequency too high
• 300753 Rotor position identification current below minimum
• 300754 Invalid signal number for variable signal function
• 300755 voltage/frequency mode
• 300756 Speed hysteresis for current setpoint smoothing invalid
• 300757 Torque limit adaptation factor invalid
• 300758 generator mode
• 300759 generator mode
• 300760 generator mode
• 300761 generator mode
• 300762 Emergency retraction/generator mode activated
• 300763 Emergency retraction/generator mode invalid
• 300764 Emergency retraction/generator mode unavailable
• 300765 Cannot measure DC bus voltage
• 300766 Stopband frequency exceeds the Shannon frequency
• 300767 Natural frequency exceeds the Shannon frequency
• 300770 format error
• 300771 asynchronous mode
• 300772 asynchronous mode
• 300774 asynchronous mode
• 300777 Rotor position identification current too large
• 300778 generator mode
• 300779 Motor moment of inertia is less than or equal to zero
• 300780 No-load current exceeds rated motor current
• 300781 No-load current greater than power unit rated current
• 300782 Reactance is less than or equal to zero
• 300783 rotor resistance invalid
• 300785 No-load current is less than or equal to zero
• 300786 Invalid field-weakening speed
• 300787 asynchronous mode
• 300788 Incorrect current control adaptation parameter settings
• 300789 This 611D control module does not support this function
• 300790 Changeover speed/velocity too small
• 300799 Data backup and restart required
• 300850 Incorrect speed control adaptive parameter settings
• 300854 Invalid signal number for variable signal function
• 300855 voltage/frequency mode
• 300858 generator mode
• 300859 generator mode
• 300860 generator mode
• 300861 generator mode
• 300862 Emergency retraction/generator mode activated
• 300863 Emergency retraction/generator mode invalid
• 300864 Emergency retraction/generator mode unavailable
• 300865 Cannot measure DC bus voltage
• 300875 Fixed DC bus voltages differ between axes
• 300888 Incorrect current control adaptation parameter settings
• 300907 Safe operating stop tolerance exceeded
• 300911 Error in one monitoring channel
• 300952 Acceptance test in progress
• 301702 track inversion incorrect
• 301703 Encoder incompatible with motor type
• 301705 Incorrect distance-coded grating parameter settings
• 301707 Safe cam modulo value parameter setting invalid
• 301708 Actual value synchronization not permitted
• 301709 Integrated linearization submodule invalid
• 301710 Motor measuring system SSI resolution invalid
• 301711 Motor measuring system SSI telegram length invalid
• 301712 Motor measuring system SSI multi-turn invalid
• 301713 Direct measuring system SSI resolution invalid
• 301714 Direct measuring system SSI telegram length invalid
• 301715 Direct measuring system SSI multi-turn invalid
• 301716 SSI direct measuring system without incremental signal unavailable
• 301717 SSI transmission timeout
• 301718 Motor/power unit combination invalid
• 310606 External valve power supply fault
• 310607 valve not responding
• 310608 Speed controller at limit
• 310609 Encoder cutoff frequency exceeded
• 310611 pressure sensor failed
• 310612 force limitation off
• 310701 Invalid speed control cycle
• 310702 Invalid position control cycle
• 310703 Invalid monitoring cycle
• 310704 Speed control cycles differ between axes
• 310705 Monitoring cycles differ between axes
• 310706 Maximum operating speed invalid
• 310707 STS configuration of axes differ
• 310708 Invalid measuring system encoder line count
• 310710 Incorrect distance-coded grating parameter settings
• 310750 Feedforward gain too high
• 310751 Speed controller proportional gain too high
• 310752 Speed controller integral gain invalid
• 310753 D component for speed controller invalid
• 310754 Friction compensation gradient too high
• 310755 Area factor too high
• 310756 Controlled system gain less than or equal to zero
• 310757 Stopband frequency exceeds the Shannon frequency
• 310758 Natural frequency exceeds the Shannon frequency
• 310759 Numerator bandwidth greater than twice the stopband frequency
• 310760 Denominator bandwidth greater than twice the natural frequency
• 310761 Force controller proportional gain too high
• 310762 Force controller integral gain invalid
• 310763 D component of force controller invalid
• 310764 Force controller controlled system gain less than or equal to zero
• 310771 Valve characteristic fine-control region gain less than or equal to zero
• 310772 Valve characteristic coarse-control region gain less than or equal to zero
• 310773 Valve characteristic saturation region end gain less than or equal to zero
• 310774 Valve characteristic zero region overlaps knee region
• 310775 Valve characteristic knee region overlaps saturation region
• 311710 Motor measuring system SSI resolution invalid
• 311711 Motor measuring system SSI telegram length invalid
• 311712 Motor measuring system SSI multi-turn invalid
• 311716 SSI measuring system without incremental signal unavailable
• 311717 SSI transmission timeout
• 380021 Profibus-DP
• 380050 Profibus-DP
• 380051 Profibus-DP
• 380060 Profibus-DP
• 380070 Profibus DP
• 380071 Profibus DP
• 380072 Profibus DP
• 380075 PROFIBUS DP: DP I/O fault
• 380500 Profibus-DP
• 380501 PROFIBUS DP: Bus/slave fault
• 380502 PROFIBUS DP: Slave configuration has changed
• 380503 PROFIBUS DP: Bus configuration has changed
• 501 Measuring circuit error (absolute current value)
• 504 Measuring circuit error (motor measuring system)
• 505 Meas.circ.error motor meas.syst.abs.track
• 507 Synchronization error rotor position
• 508 Zero pulse monitoring (motor measuring system)
• 509 Drive converter limiting frequency exceeded
• 510 Positive feedback identified
• 511 Ground fault detected
• 512 Measuring circuit error (direct measuring system)
• 513 Measuring circuit error (direct measuring system absolute track)
• 514 Zero pulse monitoring (direct measuring system)
• 515 Power module temperature out of range
• 592 Spindle positioning
• 595 Fieldbus
• 599 PROFIBUS: Cyclic data transmission interruption
• 600 Magnetic pole position not set (P1016)
• 601 AD conversion error (terminal 56/14 or 24/20)
• 602 Encoderless open-loop torque control operation is not permitted
• 603 Changeover to non-parameterized motor data set
• 604 Motor encoder not calibrated
• 605 Position controller output limited
• 606 Flux controller output limited
• 607 Current controller output limited
• 609 Encoder limit frequency exceeded
• 610 Rotor position identification failure
• 611 Illegal motion during rotor position identification
• 612 Illegal current during rotor position identification
• 615 DM encoder limiting frequency exceeded
• 616 DC link undervoltage
• 617 DC link overvoltage
• 680 Illegal motor code number
• 681 Illegal power section code number
• 682 Illegal encoder code number in P%u
• 683 Controller data calculation failure during initial commissioning
• 703 Invalid current controller cycle
• 704 Invalid speed controller cycle
• 705 Invalid position controller cycle
• 706 Invalid interpolation cycle
• 708 Axial deviations in current controller cycle
• 709 Axial deviations in speed controller cycle
• 710 Position control or interpolation cycle mismatch between axes
• 716 Invalid torque constant
• 718 BERO shutdown threshold exceeded
• 719 Motor not parameterized for delta operation
• 720 Invalid maximum motor speed
• 721 Spindle speed too high
• 722 Changeover speed/velocity too low
• 723 Axial deviations in STS configuration
• 725 Invalid encoder pulse number
• 726 Invalid voltage constant
• 727 Invalid combination of power unit and synchronous motor
• 728 Torque/current adaptation factor too high
• 729 Invalid motor stall current
• 731 Invalid rated output
• 732 Invalid rated speed
• 738 Balancing controller analog input mode error
• 739 Balancing controller axis number error
• 742 V/f operation
• 743 This control board does not support this function
• 744 Motor changeover is permitted only in closed-loop speed control mode
• 745 New EnDat encoder
• 749 Insufficient speed measurement range
• 751 Speed controller gain too high
• 753 Rotor position identification current below minimum
• 756 Invalid speed hysteresis for current setpoint smoothing
• 757 PZD config.
• 758 Setpoint source incorrectly parameterized. Supplementary info %u
• 762 This measuring system cannot use P0893
• 764 Duplicate assignment of terminal A or B (P0890)
• 765 P0890 and P0891 configure both setpoint inputs
• 766 Blocking frequency > Shannon frequency
• 767 Natural frequency > Shannon frequency
• 770 Format error
• 771 Induction motor oper.
• 772 Induction motor oper.
• 773 Not permissible to active analog input
• 774 Induction motor oper.
• 776 The older basic module does not support encoder TTL
• 777 Rotor position identification current too large
• 778 Impermissible converter frequency for rotor position ID
• 779 Invalid moment of inertia for motor %d
• 780 No-load current exceeds the rated motor current (motor %d)
• 781 No-load current of motor %d exceeds the rated current of the power unit
• 782 Reactance motor %d invalid
• 783 Invalid rotor resistance for motor %d
• 784 Invalid no-load voltage for motor %d
• 785 Invalid no-load current for motor %d
• 786 Invalid field-weakening speed for motor %d
• 787 Induction motor oper.
• 788 P0891 for drive B only
• 790 Illegal operating mode
• 791 TTL encoder interface incorrectly parameterized
• 792 Direct measuring system incorrectly parameterized
• 793 The angle encoder signal waveform differs from that of drive A
• 794 Drive B does not permit P0890=3
• 795 The normalization factor for the angle encoder position reference value is too large
• 797 Error in center frequency measurement
• 798 Measured value memory active
• 799 FEPROM backup and HW Reset required
• 800 Minus hardware limit switch
• 801 Plus hardware limit switch
• 802 The drive rotates according to the angle encoder output parameters
• 806 OC/reject traversing task missing
• 807 OC/intermediate stop missing
• 808 Reference point not set
• 809 Parking axis selected
• 810 Override in program block %n is 0
• 811 Absolute memory alarm threshold
• 814 Motor temperature prewarning
• 815 Power module temperature prewarning
• 816 Resolver sensing at its limit
• 820 Power module in i2t limiting
• 824 Function generator faulted %d
• 833 PROFIBUS: Publisher %u not connected
• 840 Teach-in for running traversing program
• 841 Teach-in for relative block
• 842 Teach-in for a relative standard block
• 843 Search velocity too high
• 845 Jogging not effective for active coupling
• 849 PLUS software limit switch actuated
• 850 MINUS software limit switch actuated 7
• 864 Parameterization error in speed controller adaptation
• 865 Invalid signal number
• 866 Incorrect current controller adaptation parameter settings
• 867 Generator mode
• 868 Regenerative operation
• 869 Reference point coordinate limited to modulo range
• 870 Jerk
• 871 Induction motor operation
• 872 Incorrect parameter setting: balancing controller P gain too high
• 875 Axial deviations in fixed voltage
• 876 Terminal function %u invalid in the current mode
• 877 Output function %u not permitted in the current mode
• 878 Input I0.x not set as equivalent zero pulse
• 879 Speed feedforward dead time constant (P0205) too large
• 881 PZD configuring
• 882 PZD configuring
• 883 PZD configuring
• 884 PZD configuring
• 885 P1261 greater than 100.0 % not permissible
• 886 Pre-tensioning torque greater than 16x rated torque
• 889 Fixed stop: axis has not reached the clamping torque
• 891 PLUS software limit switch actuated coupled
• 892 MINUS software limit switch actuated coupled
• 893 Function 73 only effective at terminal I0.x
• 894 Duplicate input assignment on the optional terminal module
• 895 Duplicate output assignment on the optional terminal module
• A01 Power board ID error
• A01006 The firmware of the DRIVE-CLiQ component must be upgraded
• A01007 DRIVE-CLiQ component requires a power cycle
• A01009 CU: Control unit overheat
• A01016 Firmware modified
• A01017 Component list has been changed
• A01019 Failure to write to removable device
• A01020 Failure to write RAM
• A01021 Use the removable device as a USB data carrier for the computer
• A01028 Configuration error
• A01032 ACX: All parameters must be stored
• A01035 ACX: Parameter backup file damaged
• A01045 CU: Invalid design data
• A01046 CU CompactFlash: Configuring data invalid
• A01047 ACX: Write to parameter error
• A01049 CU: Cannot write to file
• A01051 The project will be loaded from the memory card at the next power-on
• A01053 System overload detected
• A01054 Parameter save necessary
• A01064 CU: Internal error (CRC
• A01065 Drive: Error, inactive encoder
• A01066 Buffer memory: 70% storage capacity reached or exceeded
• A01067 Buffer memory: 100% storage capacity reached
• A01069 Parameter backup file is incompatible with the device
• A01073 Power-on is required to back up files to the memory card
• A01097 Cannot access NTP server
• A01098 RTC: Date and time settings required
• A01099 UTC synchronization tolerance exceeded
• A01100 CU: Memory card removed
• A01101 Memory card unavailable
• A01104 CU: Do not disconnect the power supply! The file system is being optimized.
• A01223 CU: Sampling time inconsistent
• A01224 CU: Pulse frequency mismatch
• A01251 CU: CU-EEPROM Data read/write error
• A01256 CU: Data read/write error on option board EEPROM
• A01304 The firmware of component DRIVE-CLiQ is not the latest version
• A01306 Upgrading the firmware of component DRIVE-CLiQ
• A01314 Topology: This component should not be present
• A01315 Drive object cannot run
• A01316 Drive object is invalid and can run again
• A01317 The disabled component is present again
• A01318 BICO: An open connection exists
• A01319 Inserted component is not initialized
• A01320 Topology: Drive object number missing from the configuration
• A01321 Topology: No drive object number in the configuration
• A01322 Topology: Duplicate drive object numbers exist in the configuration
• A01323 Topology: More than two sublists have been created
• A01324 Topology: Error creating a dummy drive object number
• A01330 Topology: Quick commissioning cannot be performed
• A01331 Topology: At least one component is not assigned to a converter
• A01358 Topology: No branch termination
• A01381 Topology: Deviation detected when comparing power units
• A01382 Topology: Deviation detected when comparing encoder modules
• A01383 Topology: Deviation detected when comparing terminal modules
• A01384 Topology: Deviation detected when comparing DRIVE-CLiQ hub modules
• A01385 Topology: Controller extension module inserted in the wrong position
• A01386 Topology: DRIVE-CLiQ component inserted in the wrong position
• A01387 Topology: Comparison, option slot component shifte
• A01388 Topology: Deviation detected when comparing EnDat encoders
• A01389 Topology: Deviation detected when comparing motors with DRIVE-CLiQ
• A01416 Topology: Additional component in the actual topology
• A01420 DRIVE-CLiQ component deviation
• A01421 Topology: Comparison, different components
• A01425 Topology: Deviation detected when comparing component serial numbers
• A01428 Topology: Deviation detected when comparing component connections
• A01429 Topology: Deviation detected when comparing multiple component connections
• A01481 Topology comparison: Power unit missing from the actual topology
• A01482 Missing DRIVE-CLiQ component: Encoder module
• A01483 Topology comparison: Terminal module missing from the actual topology
• A01484 Topology comparison: DRIVE-CLiQ hub module missing from the actual topology
• A01485 Topology: Comparison detected that CX32 is missing from the actual topology
• A01486 Topology comparison: DRIVE-CLiQ component missing from the actual topology
• A01487 Topology comparison: "Option slot component" missing from the actual topology
• A01488 Topology: EnDat encoder missing from the actual topology
• A01489 Topology comparison: Motor with DRIVE-CLiQ missing from the actual topology
• A015 Simolink start start
• A01507 BICO: Connection to an inactive object exists
• A01508 BICO: Number of connections to inactive objects exceeded
• A01514 BICO: Error writing during reconnection
• A01550 Network security: Drive data encryption invalid
• A01552 Network security: cannot access the syslog server
• A01553 Network security: temporary overflow of the syslog server send buffer
• A01554 Network security: Connection to the syslog server interrupted
• A01555 Network security: syslog server certificate validation failure
• A01556 Safety: local log storage is about to switch to circular mode.
• A01557 Safety: local log storage is in circular mode.
• A01561 Network security: Authentication failure alarm
• A01570 Network security: invalid security certificate
• A01571 Network safety: Certificate management event
• A01590 Drive: Motor maintenance interval expired
• A01605 SI: Checksum error
• A01631 SI P1: Motor brake applied (holding)/SBC configuration is meaningless
• A01637 SI: Safety configuration is not protected
• A01638 SI: Safety password entered
• A01654 SI P1 (CU): Configuration differs from PROFIsafe
• A01666 SI motion P1 (CU): Static 1 signal on F-DI for safety response
• A01669 SI Motion: Invalid motor and power unit combination
• A01678 SI: A mandatory fault check for "Execute STO via the power module terminals" is required
• A01691 SI Motion: Ti and To are not suitable for the DP cycle
• A01693 SI P1 (CU): Safety parameters have been modified; power-on is required
• A01695 SI Motion: Encoder module replaced
• A01696 SI motion: Forced fault check for motion monitoring selected during start
• A01697 SI motion: Forced fault check for motion monitoring required
• A01698 SI P1 (CU): Commissioning mode active
• A01699 SI P1 (CU): A forced fault check of STO is required
• A01706 SI Motion P1 (CU): SAM/SBR limit exceeded
• A01707 SI motion P1: Safe Operating Stop tolerance exceeded
• A01709 SI motion P1: SS2E triggered
• A01711 SI Motion P1 (CU): Fault in a monitoring channel
• A01730 SI motion P1: Reference program block for dynamically safely limited speed is invalid
• A01750 SI motion P1: Encoder hardware fault
• A01751 SI motion P1: Safety encoder validity test fault
• A01774 SI motion P1 (CU): A forced fault check of the fail-safe digital output is required
• A01780 SBT: Brake already applied when selected
• A01781 SBT brake release time exceeded
• A01782 SBT brake test: Control error
• A01783 SBT brake application time exceeded
• A01785 SBT brake test configuration error
• A01788 SI: Auto forced fault check waiting for cancellation by motion monitoring STO
• A01789 Auto test stop and brake test must not be enabled when test stop is selected
• A01790 SI: Start aborted by STO via terminal
• A01794 SI motion: Check modal values when enabling PROFIsafe safe position
• A01796 SI P1 (CU): Waiting for communication
• A01798 SI Motion P1 (CU): Forced fault check of motion monitoring is in progress
• A01799 SI Motion P1 (CU): Acceptance test mode is active
• A018 Digital output short circuit
• A01839 DRIVE-CLiQ diagnostics: Component cable fault
• A01840 SMI: Component without motor data detected
• A019 From free function blocks
• A01900 "PB/PN: Configuration telegram error"
• A01901 "Parameterizing telegram incorrect"
• A01902 "PB/PN: Clock cycle synchronous operation paramete
• A01903 COMM INT: Receive configuration data invalid
• A01904 PN: Master PZD telegram setting rejected
• A01905 PN: Master setting for activating channel diagnostics rejected
• A01906 EtherNet/IP: Configuration error
• A01920 PROFIBUS: Cyclic connection interruption
• A01921 PROFIBUS: Setpoint received after To
• A01925 Modbus TCP: Connection interruption
• A01930 PB/PN: Current loop sampling times differ in isochronous synchronization
• A01931 PB/PN: Speed loop sampling times differ in isochronous synchronization
• A01932 "PB/PN clock cycle synchronization missing for DSC
• A01940 PB/PN: Isochronous synchronization not achieved
• A01941 PB/PN: Cyclic signal missing in bus topology
• A01943 PB/PN: Interference affecting cyclic signal in bus topology
• A01944 PB/PN sign-of-life synchronization not achieved
• A01945 PROFIBUS: Connection fault with the publisher
• A01953 CU SYNC: Synchronization not completed
• A01955 CU DRIVE-CLiQ: DO synchronization not completed
• A01970 CBE25: Cyclic connection interruption
• A01971 CBE2x: Maximum number of controllers exceeded
• A01977 CBE41: Overtemperature alarm
• A01979 CBE2x: Internal error during cyclic data transfer
• A01980 PN: Cyclic connection interruption
• A01981 PN: Maximum number of controllers exceeded
• A01982 PN: Second controller missing
• A01983 PN: System redundancy switchover in progress
• A01989 PN: Internal error during cyclic data transfer
• A01990 USS: PZD configuration error
• A01991 AS-i: Parameter setting mismatch
• A02 Parameter error
• A020 From free function blocks
• A02000 Function generator: Cannot start
• A02005 Function generator: Drive does not exist
• A02006 Function generator: No drive specified for connection
• A02007 Function generator: Drive is not SERVO/VECTOR/DC_CTRL
• A02008 Function generator: Drive assigned multiple times
• A02009 Function generator: Incorrect operating mode
• A02010 Function generator: Drive speed setpoint is not zero
• A02011 Function generator: Actual drive speed is not zero
• A02015 Function generator: Drive enable missing
• A02016 Function generator: Field build-up in progress
• A02020 Function generator: Parameter cannot be changed
• A02025 Function generator: Period too short
• A02026 Function generator: Pulse width too large
• A02030 Function generator: Physical address is zero
• A02040 Function generator: Incorrect offset value
• A02041 Function generator: Incorrect bandwidth value
• A02047 Function generator: Invalid time slice period
• A02050 Trace: Cannot start
• A02051 Trace: Recording is not possible due to know-how protection
• A02055 Trace: Recording time too short
• A02056 Trace: Recording cycle too short
• A02057 Trace: Invalid time slice period
• A02058 Trace: Invalid time slice period for cyclic trace
• A02059 Trace: Invalid time slice cycle for recording channel 2 x 8
• A02060 Trace: No signals specified for recording
• A02061 Trace: Invalid signal
• A02062 Trace: Invalid trigger signal
• A02063 Trace: Invalid data type
• A02070 Trace: Parameter cannot be changed
• A02075 Trace: Pretrigger time too long
• A02085 Reporting function: Parameter setting error
• A02095 MTrace 0: Cannot activate multiple tracing
• A02096 MTrace 0: Cannot save
• A02097 MTrace 1: Cannot activate multiple traces
• A02098 MTrace 1: Cannot save
• A02099 Trace: Insufficient storage space in the control unit
• A02100 Drive: Current loop computation dead time too short
• A02150 TEC: Technology Extension cannot be loaded
• A025 Carbon brushes too short
• A026 Poor bearing status
• A027 Airflow monitoring
• A028 Motor
• A029 Motor overheat
• A03 Failed to save user parameters to flash memory. Replace the drive.
• A031 Speed controller monitoring
• A035 Drive stalled
• A03501 TM: Sampling time modified
• A03506 24 V power supply missing
• A03507 Digital output not set
• A03510 TM: Implausible calibration data
• A03520 Temperature sensor fault
• A03550 TM: Speed setpoint filter natural frequency > Shannon frequency
• A03560 LRC: Key switch status is "Off"
• A03561 LRC: Key switch status is "Manual run"
• A036 No armature current flowing
• A037 I2t Motor motor
• A038 Overspeed
• A039 The I2t value of the power unit is too high
• A04 2. Drive damaged
• A043 If during operation
• A044 An alarm from a slave rectifier connected to the parallel interface is valid
• A0452 Fault
• A046 Configurable analog input used as the main reference
• A047 Configurable analog input
• A04787 "Reject traversing task
• A05 Motor operation
• A05000 Power unit: Inverter heatsink overheat
• A05001 Power unit: Insulation layer chip overheat
• A05002 Power unit: Air inlet overheat
• A05003 Power unit: internal space overheat
• A05004 Power unit: Rectifier overheat
• A05005 Cooling unit: Coolant volumetric flow rate too low
• A05006 Power unit: Thermal model overheat
• A0501 Current limit
• A0502 Overvoltage limit
• A0503 Undervoltage limit
• A0504 Converter overtemperature
• A0505 Converter I2T overtemperature
• A05052 Parallel circuit: Current imbalance error
• A05053 Parallel circuit: DC bus voltage imbalance error
• A05054 Parallel circuit: Power unit disabled
• A0506 Inverter load duty cycle
• A05065 Implausible voltage measurement
• A05066 Parallel circuit: VSM voltage imbalance error
• A05070 Parallel circuit: Energy input imbalance during precharging
• A0510 Motor overtemperature
• A0511 Motor I2T overtemperature
• A0512 Motor temperature signal loss
• A0520 Rectifier overtemperature
• A0521 Ambient temperature too high
• A0522 I2C read timeout
• A0523 Output fault- output fault
• A053 From free function blocks
• A0535 Brake resistor hot
• A054 From free function blocks
• A0541 Motor data identification routine active
• A0542 Activate speed control
• A0571 Auto restart after fault present
• A059 Temporarily activated process option
• A0590 Speed encoder no-signal alarm
• A06 Switch on the main power supply.
• A0600 Alarm: RTOS exceeded the allowable range
• A06105 Infeed: Main power supply undervoltage
• A06205 Infeed: Voltage dip in at least one mains phase
• A06208 Infeed: Supply voltage asymmetry
• A06215 Infeed: Total current too high
• A06260 Infeed: Input filter overtemperature
• A06301 Infeed: Main power supply overvoltage
• A06350 "Infeed: Measured line frequency too high"
• A06351 "Infeed: Measured line frequency too low"
• A06400 Infeed: Mains data detection selected/active
• A06502 Infeed: Not synchronized with the main supply during transformer field excitation
• A06601 Infeed: Interruption of current deviation measurement
• A06602 Infeed: Cannot perform current offset measurement
• A067 Rectifier cooling fault
• A06800 Infeed: Maximum steady-state DC bus voltage reached
• A06810 Infeed: DC bus voltage below alarm threshold
• A06849 Infeed: Short-circuit operation active
• A06900 Braking module: Fault (1 -> 0
• A06901 Braking module: I2t shutdown prewarning
• A06904 Braking module internally disabled
• A06905 Braking module internal I2t open-circuit alarm message
• A06921 Braking resistor phase asymmetry
• A06925 Run mode for diagnostics only
• A0700 Modify the PROFIBUS configuration
• A0701 CB alarm 2
• A07012 I2t Motor module overtemperature
• A07014 Drive: Motor temperature model configuration alarm
• A07015 Drive: Motor temperature sensor alarm message
• A07016 "Motor temperature
• A07017 Additional temperature alarm threshold exceeded
• A0702 Check the connectors, cables, and PROFIBUS master
• A0703 Check the setpoint from the PROFIBUS master.
• A0704 Start the intermediate node
• A0705 None (converter fault).
• A0706 No diagnostic information for r2041
• A0707 CB alarm 8
• A0708 CB alarm 9
• A07089 Unit conversion: Function block cannot be activated after unit conversion
• A0709 CB alarm 10
• A07091 Drive: Measured current loop dynamic response invalid
• A07092 Drive: Inertia estimator not yet complete
• A07094 Common parameters out of range
• A07095 Drive: One-button tuning active
• A0710 The communication port on the control unit may be faulty
• A0711 Check the P0918 address setting and parameter P
• A07140 Drive: Current loop sampling time incompatible with the spindle
• A07200 Drive: Master control issues ON command
• A07314 Flying restart is not performed when exiting bypass
• A07321 Drive: Auto restart activated
• A07325 Drive: Sleep mode activated - drive switches back on automatically
• A07329 Drive: kT evaluator, kT(iq) characteristic curve or voltage compensation failure
• A07350 Drive: Measuring probe configured as a digital output
• A07351 Drive: Measuring probe configured as a digital output
• A07352 Drive: Implausible limit switch signal
• A07353 Drive: DC control disabled
• A07354 Drive: Cannot perform cogging torque compensation
• A07356 Drive configuration: Cogging torque compensation: Motor or encoder serial number mismatch
• A07391 DC bus capacitor reforming active
• A07400 Drive: Maximum DC bus voltage controller active
• A07401 Drive: Maximum DC bus voltage controller disabled
• A07402 Drive: Minimum DC bus voltage controller active
• A07408 Drive: Minimum DC bus voltage controller disabled
• A07409 Drive: V/f Control current limit controller active
• A07416 Drive: Flux controller configuration
• A07424 Drive: Invalid operating conditions for APC
• A07427 Motor switch-on alarm
• A07428 Process controller parameter setting error
• A07440 EPOS: Jerk time limit reached
• A07441 Position loop: Back up the position offset for absolute encoder adjustment
• A07444 PID Auto tuning activated
• A07454 Position loop: No valid encoder for actual position value processing
• A07455 EPOS: Maximum speed limited
• A07456 EPOS: Set speed is limited
• A07457 EPOS: Incorrect input signal combination
• A07461 EPOS: Reference point not set
• A07462 EPOS: Selected traversing block number does not exist
• A07463 EPOS: External block change not requested in the traversing block
• A07465 EPOS: Traversing block has no subsequent block
• A07466 EPOS: Traversing block number assigned multiple times
• A07467 EPOS: Traversing block contains incorrect task parameters
• A07468 EPOS: Traversing block jump destination does not exist
• A07469 EPOS: Traversing block target position < negative software limit switch
• A07470 EPOS: Traversing block target position > positive software limit switch
• A07471 EPOS: Traversing block target position outside the modulo range
• A07472 EPOS: Traversing block ABS_POS/ABS_NEG not possible
• A07473 EPOS: Start of traversing range reached
• A07474 EPOS: End of traversing range reached
• A07477 EPOS: Target position < negative software limit switch
• A07478 EPOS: Target position > positive software limit switch
• A07479 EPOS: Approaching negative software limit switch
• A07480 EPOS: Approaching positive software limit switch
• A07483 EPOS: Clamping torque not reached when traveling to a fixed stop
• A07486 EPOS: Intermediate stop missing
• A07487 EPOS: Run task cancellation missing
• A07489 EPOS: Reference point compensation outside the window
• A07495 Position loop: Referencing function interruption
• A07496 EPOS: Cannot be enabled
• A07497 Position loop: Position setpoint activated
• A07498 Position loop: Measuring probe evaluation cannot be performed
• A07504 Drive: Motor data set is not assigned to a drive data set
• A07505 EPOS: Fixed stop task cannot be executed in V/f/SLVC control
• A07506 EPOS: Check the BICO interconnection between EPOS and the position loop
• A07507 EPOS: Reference point cannot be set
• A07512 Drive: Encoder data set changeover cannot be param
• A07514 Drive: Data structure does not match interface mode
• A07515 Drive: Power unit and motor incorrectly connected
• A07517 Drive: Encoder data set changeover incorrectly par
• A07519 Drive: Incorrect parameter setting for motor switching
• A07520 Drive: Cannot perform motor switchover
• A07530 Drive: Drive data set DDS does not exist
• A07531 Drive: Command data set CDS does not exist
• A07532 Drive: Encoderless closed-loop control has not yet been commissioned
• A07541 Drive: Cannot switch data sets
• A07550 Drive: Cannot reset encoder parameters
• A07557 Encoder 1: Permissible range exceeded by reference point coordinate
• A07558 Encoder 2: Reference point coordinate exceeded the permissible range
• A07559 Encoder 3: Reference point coordinates exceeded the permissible range
• A07565 Drive: Encoder error on PROFIdrive encoder interface 1
• A07566 Drive: Encoder error in PROFIdrive encoder interfa
• A07567 Drive: Encoder error in PROFIdrive encoder interfa
• A07569 Encoder cannot be detected
• A07576 Drive: Encoderless operation active due to a fault
• A07577 Encoder 1: Measuring head analysis cannot be performed
• A07578 Encoder 2: Measuring head analysis cannot be performed
• A07580 Drive: Incorrect component number for encoder module
• A07581 Encoder 1: Error in actual position value processing
• A07582 Encoder 2: Error in actual position value processing
• A07583 Encoder 3: Error processing the actual position value
• A07584 Encoder 1: Position setting value activated
• A07585 Encoder 2: Position setpoint activated
• A07586 Encoder 3: Activate position setting value
• A07587 Encoder 1: No valid encoder for actual position value processing
• A07588 Encoder 2: No valid encoder for actual position value processing
• A07589 Encoder 3: No valid encoder for actual position value processing
• A07590 Encoder 1: Drive data set switched during operation
• A07591 Encoder 2: Drive data set switched during operation
• A07592 Encoder 3: Drive data set switching during operation
• A07593 Encoder 1: Actual position value range exceeded
• A07594 Encoder 2: Actual position value range exceeded
• A07595 Encoder 3: Actual position value range exceeded
• A07596 Encoder 1: Reference function interruption
• A07597 Encoder 2: Referencing function interruption
• A07598 Encoder 3: Referencing function interruption
• A07805 Drive: Power unit overload I2t
• A07820 Drive: Temperature sensor not connected
• A07823 I2t monitoring alarm threshold exceeded
• A07825 Drive: Simulation mode activated
• A07850 External alarm 1
• A07851 External alarm 2
• A07852 External alarm 3
• A07891 Drive: Pump/fan stall monitoring
• A07892 Drive: Pump/fan no-load monitoring
• A07893 Drive: Pump leakage monitoring
• A07899 Drive: Cannot perform stall monitoring
• A07903 Drive: Motor speed difference
• A07904 External armature short circuit: Contactor feedback "closed" missing
• A07908 Internal armature short circuit active
• A07910 Drive: Motor overtemperature
• A07918 Select/activate AC setting encoder operation
• A07920 Torque/speed too low
• A07921 Drive: Torque/speed too large
• A07922 Drive: Torque/speed out of tolerance
• A07923 "Torque too low"
• A07924 "Torque too high"
• A07925 "Torque outside tolerance"
• A07926 Drive: Invalid envelope parameters
• A07927 DC braking active
• A07929 Drive: Motor cannot be detected
• A07931 Holding brake does not release
• A07932 Holding brake does not apply
• A07941 "Line supply-drive" synchronization: Incorrect target frequency
• A07942 "Main power supply-drive" synchronization: Set frequency differs significantly from target frequency
• A07943 "Line supply-drive" synchronization: Synchronization not permitted
• A07960 Drive: Friction characteristic curve error
• A07961 Drive: Friction characteristic curve recording active
• A07963 "Friction characteristic plot interrupted".
• A07965 Drive: Save required
• A07967 Converter: Auto encoder zero alignment/magnetic pole position identification error
• A07971 Drive: Commutation angle offset determination active
• A07972 Drive: Emergency mode (EOM) activated
• A07975 Drive: Run after zero pulse detection - waiting for setpoint preset
• A07976 Drive: Encoder fine adjustment activated
• A07978 Drive: Active ESM mode is waiting for motor data detection to finish
• A07979 Drive: Pole position detection requires calibration
• A07980 Rotating measurement active
• A07981 Rotating measurement not enabled
• A07987 Drive: No encoder available for rotation detection
• A07991 Motor data detection active
• A07994 Drive: Motor data detection not performed
• A07998 Drive: Motor data detection on another drive is valid
• A07999 Drive: Motor data detection cannot be activated
• A08 1. Encoder UVW signal damaged
• A08504 PN/COMM BOARD: Internal error during cycle count transmission
• A08511 PROFINET: Received configuration data invalid
• A08520 COMM BOARD: Non-cyclic channel error
• A08526 PN/COMM BOARD: No cyclic connection
• A08530 PN/COMM BOARD: Information channel error
• A08531 CBE20 requires power-on again
• A08550 PZD interface hardware assignment fault
• A08555 Modbus TCP: Commissioning error
• A08560 IE: Configuration file syntax error
• A08561 IE: Parameter setting consistency error
• A08562 PROFINET: Syntax error in the configuration file
• A08563 PROFINET: Adjustable parameter consistency error
• A08564 PN/COMM BOARD: Configuration file syntax error
• A08565 PROFINET: Parameter setting consistency error
• A08566 IIoT: Configuration file syntax error
• A08567 IIoT: Adjustable parameter consistency error
• A08751 CAN: Message loss
• A08752 CAN: Fault counter for passive faults exceeded
• A08753 CAN: Message buffer overflow
• A08754 CAN: Communication mode fault
• A08755 CAN: Object cannot be mapped
• A08756 CAN: Number of mapped bytes exceeded
• A08757 CAN: COB-ID setting invalid
• A08758 CAN: Maximum number of valid PDO exceeded
• A08759 CAN: PDO COB-ID already exists
• A08760 CAN: maximum number of IF PZD exceeded
• A08800 PROFIenergy energy-saving mode active
• A08802 PROFIenergy Cannot switch off incremental encoder power supply
• A09 1. Encoder ABZ connection fault
• A09000 Webserver User configuration error
• A0910 Vdc_max controller inactive
• A0911 Vdc_max controller active
• A0912 DC circuit minimum
• A0920 ADC parameters not correctly set
• A0921 DAC parameter setting
• A0922 No load at the inverter
• A0923 Forward jog and reverse jog requested simultaneously
• A0936 PID auto tuning active - PID Auto-tuning active
• A0952 Fault
• A1009 Control unit overheat
• A1019 Failure to write to removable device
• A1032 All parameters need to be saved
• A1045 Invalid configuration data
• A128 TB alarm
• A13000 Insufficient license
• A13001 License checksum error
• A13002 Insufficient licenses; cannot run
• A13021 No license available for 600 Hz
• A13030 Trial license activated
• A13031 Trial license trial period expired
• A13032 Final trial period of trial license activated
• A13033 Final trial period of the trial license has expired
• A14 Internal software fault occurred. Reset by cycling power.
• A1774 A forced fault check of the fail-safe digital output is required. The preset forced fault check interval for the fail-safe digital output (F-DO) has been exceeded.
• A1902 PROFIdrive: Incorrect setting for isochronous run
• A1920 DriveBus bus: Setpoint received after To
• A1932 DSC lacks DriveBus bus cycle isochronous synchronization
• A1940 PROFIdrive: Isochronous synchronization not achieved
• A1944 PROFIdrive: Sign-of-life synchronization not achieved
• A21 Motor operation
• A22 Load too large
• A23 1. Low supply voltage
• A29010 Infeed: Power unit cyclic data heartbeat signal error
• A29032 Infeed: Hardware current limit activated in power unit phase V
• A29033 Infeed: Hardware current limit activated in power unit phase W
• A29034 Infeed: Power unit internal compartment overheat
• A29041 Infeed: Power unit 24/48 V undervoltage alarm
• A29042 Infeed: The power unit fan has reached its maximum operating hours
• A29044 Infeed: Power unit 24/48 V overvoltage alarm
• A29046 Infeed: Power unit undervoltage alarm
• A29048 Infeed: Power unit fan damaged
• A29049 Infeed: Power unit 24 V electronics power supply overload
• A29057 Infeed: Power unit mains imbalance
• A29066 Infeed: Power unit capacitor air outlet overheat alarm
• A29086 Infeed: The power unit coolant temperature has exceeded the alarm threshold
• A29250 Infeed: Power unit rectifier heatsink overheat
• A29252 Infeed: Power unit chip overheat alarm
• A29253 "Overtemperature thermal model"
• A29254 Infeed: Power unit inlet air overheat alarm
• A29256 Infeed: Power unit I2t overload
• A29266 Infeed: Power unit cannot achieve the required modulator settings
• A29269 Infeed: Internal hardware fault in the power unit
• A29500 Power loss in the power supply filter capacitor exceeded the alarm threshold
• A29853 Infeed: Power unit cyclic data heartbeat signal error
• A29920 Infeed: Power unit temperature sensor fault
• A29999 Infeed: Unknown power unit alarm
• A30010 Power unit: Cyclic data sign-of-life error
• A30016 Power unit: Load power supply disabled
• A30030 Power unit: Internal space overtemperature alarm
• A30031 Power unit: Hardware current limit response for phase U
• A30032 Power unit: Hardware current limit activated for phase V
• A30033 Power unit: Hardware current limit activated for phase W
• A30034 Power unit: internal space overheat
• A30041 Power unit: 24/48 V undervoltage alarm
• A30042 Power unit: Fan has reached its maximum run time
• A30044 Power unit: 24/48 V Overvoltage alarm
• A30046 Power unit: Undervoltage alarm
• A30048 Power unit: External fan damaged
• A30049 Power unit: Internal fan damaged
• A30054 Power unit: Undervoltage when releasing the brake
• A30057 Power unit: Power supply imbalance
• A30065 Implausible voltage measurement
• A30066 Power unit: Capacitor air outlet overheat alarm
• A30073 Actual value/setpoint processing is no longer synchronized
• A30076 Power unit: Braking resistor thermal overload alarm
• A30077 Power unit: Braking resistor thermal overload
• A30079 Power unit: DC bus voltage too high relative to input voltage
• A30082 Power unit: Coolant volumetric flow rate too low; alarm threshold exceeded
• A30086 Power unit: Coolant temperature exceeded the alarm threshold
• A30096 Power unit: Balancing resistor thermal overload alarm
• A30250 Power unit: Inverter heatsink overheat
• A30251 Power unit: Rectifier overheat
• A30252 Power unit: Chip overheat alarm
• A30253 Power unit: Thermal model overheat alarm
• A30254 Power unit: Inlet air overheat alarm
• A30256 Power unit: I2t overload (AC
• A30257 Power unit: I2t overload (DC
• A30259 Braking resistor resistance too low
• A30266 Power unit: Cannot implement the required modulator settings
• A30267 Power unit: Active power overload
• A30269 Power unit: Internal hardware fault
• A30315 Power unit: 24 V power supply overloaded by PM
• A30502 Power unit: DC bus overvoltage
• A30605 SI: Checksum error
• A30666 SI motion P2: A logic 1 signal is continuously present on F-DI for safety acknowledgment
• A30693 SI P2: Safety parameters have been modified; power-on is required again
• A30706 SI Motion P2: SAM/SBR limit exceeded
• A30707 SI motion P2: Safe operating stop tolerance exceeded
• A30709 SI motion P2: SS2E triggered
• A30711 SI motion P2: Fault in a monitoring channel
• A30714 SI Motion P2: Safely-Limited Speed exceeded
• A30716 SI motion P2: Safe direction of motion tolerance exceeded
• A30730 SI Motion P2: The reference program segment for the dynamic safely-limited speed is invalid
• A30788 Auto test stop: Waiting for STO to be canceled via SMM
• A30798 SI motion P2: Forced fault check for motion monitoring in progress
• A30799 SI motion P2: Acceptance test mode valid
• A30804 Power unit: CRC
• A30810 Power unit: watchdog timer
• A30853 Power unit: Cyclic data sign-of-life error
• A30903 Power unit: I2C bus
• A30919 Power unit: Temperature monitoring impaired
• A30920 Power unit: temperature sensor fault
• A30930 Power unit: Component tracking data saved
• A30999 Power unit: Unknown alarm
• A31400 Encoder 1: Zero pulse spacing error (alarm threshold exceeded
• A31401 Encoder 1: Zero pulse fault (alarm threshold exceeded
• A31407 Encoder 1: Function limit reached
• A31410 Encoder 1: Serial communication
• A31411 Encoder 1: Absolute encoder alarm
• A31412 Encoder 1: Fault bit set in the serial record
• A31414 Encoder 1: Amplitude error in signal C or D (C^2 + D^2
• A31418 Encoder 1: Speed difference per sampling interval exceeded
• A31419 Encoder 1: Signal A or B exceeded tolerance
• A31421 Encoder 1: Measured commutation position error (alarm
• A31422 Encoder 1: Square-wave encoder pulse count outside tolerance
• A31429 Encoder 1: Position difference between Hall sensor/signal C/D and signal A/B is too large
• A31431 Encoder 1: Incremental/absolute position offset too large
• A31432 Encoder 1: Rotor position adaptation error
• A31442 Encoder 1: Battery voltage prewarning
• A31443 Encoder 1: Unipolar CD signal level exceeded specification
• A31460 Encoder 1: Analog encoder channel A fault
• A31461 Encoder 1: Analog encoder channel B fault
• A31462 Encoder 1: no analog encoder channel
• A31463 Encoder 1: Analog sensor position value exceeds the limit
• A31470 Encoder 1: Encoder reports internal error (X521.7
• A31700 Encoder 1: Functional safety monitoring triggered
• A31811 Motor encoder: Encoder serial number changed
• A31840 Encoder 1 DRIVE-CLiQ: Below threshold
• A31902 Encoder 1: SPI-BUS fault occurred
• A31903 Encoder 1: I2C-BUS fault occurred
• A31915 Encoder 1: Configuration error
• A31920 Encoder 1: Temperature sensor fault
• A31930 Encoder 1: The data logger saved diagnostic data
• A31940 Encoder 1: Spindle sensor S1 voltage error
• A31999 Encoder 1: Unknown alarm
• A32400 Encoder 2: Zero pulse distance error (alarm threshold exceeded
• A32401 Encoder 2: zero pulse fault (alarm threshold exceeded
• A32407 Encoder 2: Function limit reached
• A32410 Encoder 2: Serial communication
• A32411 Encoder 2: Absolute encoder alarm
• A32412 Encoder 2: Fault bit set in the serial record
• A32414 Encoder 2: Amplitude error in signal C or D (C^2 + D^2
• A32418 Encoder 2: Speed difference per sampling rate exce
• A32419 Encoder 2: Signal A or B out of tolerance
• A32421 Encoder 2: measured commutation position error (alarm
• A32422 Encoder 2: Square-wave encoder pulse count outside tolerance
• A32429 Encoder 2: Position difference between Hall sensor/signal C/D and signal A/B is too large
• A32431 Encoder 2: Incremental/absolute position offset too large
• A32432 Encoder 2: Rotor position adaptation error
• A32442 Encoder 2: Battery voltage prewarning
• A32443 Encoder 2: Unipolar CD signal level exceeded specification
• A32460 Encoder 2: Analog encoder channel A fault
• A32461 Encoder 2: Analog encoder channel B fault
• A32462 Encoder 2: no analog encoder channel active
• A32463 Encoder 2: Analog sensor position value exceeds limit
• A32470 Encoder 2: Encoder reports internal error (X521.7
• A32700 Encoder 2: Plausibility test did not produce the expected value
• A32811 Encoder 2: Encoder serial number has changed
• A32902 Encoder 2: SPI-BUS fault occurred
• A32903 Encoder 2: I2C-BUS fault occurred
• A32915 Encoder 2: Configuration error
• A32920 Encoder 2: Temperature sensor fault
• A32930 Encoder 2: Data recorder has saved diagnostic data
• A32940 Encoder 2: Spindle sensor S1 voltage error
• A32999 Encoder 2: Unknown warning
• A33400 Encoder 3: Zero pulse spacing error (alarm threshold exceeded
• A33401 Encoder 3: Zero pulse fault (alarm threshold exceeded
• A33407 Encoder 3: Functional limit reached
• A33410 Encoder 3: Communication fault (encoder and encoder module
• A33418 Encoder 3: Speed difference per sampling rate exce
• A33419 Encoder 3: Track A or B outside the tolerance rang
• A33421 Encoder 3: Measured commutation position incorrect (alarm
• A33422 Encoder 3: Square-wave encoder pulse count outside tolerance
• A33429 Encoder 3: Position difference between Hall sensor/signal C/D and signal A/B too large
• A33431 Encoder 3: Incremental/absolute position difference too large (alarm
• A33432 Encoder 3: Rotor position alignment correction error
• A33442 Encoder 3: Battery voltage alarm threshold reached
• A33460 Encoder 3: Analog encoder channel A fault
• A33461 Encoder 3: Analog encoder channel B fault
• A33462 Encoder 3: No channel for analog encoder
• A33463 Encoder 3: Analog sensor position value exceeded the limit
• A33470 Encoder 3: Contamination detected
• A33700 Encoder 3: Validity test did not produce the expected value
• A33811 Encoder 3: Encoder serial number has changed
• A33840 Encoder 3 DRIVE-CLiQ: Below threshold
• A33902 Encoder 3: SPI-BUS fault occurred
• A33903 Encoder 3: I2C-BUS fault occurred
• A33915 Encoder 3: Configuration error
• A33920 Encoder 3: Temperature sensor fault
• A33930 Encoder 3: The data logger saved diagnostic data
• A33940 Encoder 3: Spindle sensor S1 voltage error
• A33999 Encoder 3: Unknown alarm
• A34211 VSM: Temperature alarm threshold exceeded
• A34807 VSM: Sequence control time monitoring
• A34840 VSM DRIVE-CLiQ: Below threshold
• A34903 VSM: I2C-Bus bus fault occurred
• A34904 VSM: EEPROM
• A34905 VSM: Parameter access
• A34920 fault, temperature sensor
• A34999 VSM: Unknown alarm
• A35012 TM54F: Forced fault check of fail-safe digital inputs/outputs in progress
• A35014 TM54F: Forced latent fault check required
• A35054 TM54F: Temperature alarm threshold exceeded
• A35075 TM54F: Internal communication fault
• A35080 TM54F: Safety parameter checksum error
• A35081 TM54F: Steady-state 1 signal present on F-DI for safety acknowledgment
• A35211 Channel 0
• A35212 TM: Channel 1 temperature alarm threshold exceeded
• A35213 TM: Channel 2 temperature warning threshold exceeded
• A35214 Channel 3
• A35222 TM: Encoder line count error
• A35223 TM: Zero pulse offset error
• A35224 TM: Zero pulse synchronization interruption
• A35225 TM: Zero pulse synchronization stopped - encoder not ready
• A35226 TM: Signal A/B not active
• A35227 EDS switching/encoder data set change not supported
• A35228 TM: Invalid sampling time p4099[3]
• A35231 TM: Missing "Control via PLC"
• A35232 TM41: Zero pulse not synchronized; power-on required
• A35300 TM: Power supply +/-15 V error
• A35301 TB: 24V undervoltage
• A35302 TB: 24V overvoltage
• A35410 Channel 4
• A35411 TM: Channel 5 temperature alarm threshold exceeded
• A35412 TM: Channel 6 temperature alarm threshold exceeded
• A35413 Channel 7
• A35414 Channel 8
• A35415 Channel 9
• A35416 Channel 10
• A35417 Channel 11
• A35801 TM DRIVE-CLiQ: Sign-of-life missing
• A35802 TM: Time slice overflow
• A35803 TM: Memory test
• A35804 TM: CRC
• A35805 TM: EPROM checksum error
• A35807 TM: Sequence control time monitoring
• A35840 TM DRIVE-CLiQ: Below threshold
• A35903 TM: I2C bus fault occurred
• A35904 TM: EEPROM
• A35905 TM: Parameter access
• A35906 TM: 24 V power supply missing
• A35907 TM: Hardware initialization failure
• A35910 TM: Module overheat
• A35911 TM: Sign-of-life fault in isochronous run
• A35920 TM: Channel 0 temperature sensor fault
• A35921 TM: Channel 1 temperature sensor fault
• A35922 TM: Channel 2 temperature sensor fault
• A35923 TM: Channel 3 temperature sensor fault
• A35924 TM: Channel 4 temperature sensor fault
• A35925 TM: Channel 5 temperature sensor fault
• A35926 TM: Channel 6 temperature sensor fault
• A35927 TM: Channel 7 temperature sensor fault
• A35929 TM: Channel 9 temperature sensor fault
• A35930 TM: Channel 10 temperature sensor fault
• A35931 TM: Channel 11 temperature sensor fault
• A35999 TM: Unknown alarm
• A36211 Hub: Component overheat alarm
• A36217 Hub: 24 V power supply undervoltage alarm
• A36801 DRIVE-CLiQ hub: Sign of life missing
• A36802 Hub: Time slice overflow
• A36804 DMC: CRC
• A36805 DMC: EPROM checksum error
• A36840 DRIVE-CLiQ hub: Below threshold
• A36999 Hub: Unknown alarm
• A37034 HF damper: Internal compartment overtemperature
• A37041 HF damper: 24 V undervoltage alarm
• A37044 HF Damper: 24 V overvoltage alarm
• A37049 HF Damper: Internal fan damaged
• A37056 HF damper: Heatsink overheat
• A37310 HF reactor: Overtemperature
• A37312 HF Reactor: Overtemperature or fan fault
• A37502 HF Damper: Damping voltage too high
• A37801 HF Damper: Missing sign of life
• A37999 HF Damper: Unknown alarm
• A38042 AIM: Fan has reached its maximum operating time
• A38432 AIM: Component temperature exceeded the alarm threshold
• A38433 AIM: Power supply reactor core temperature exceeded the alarm threshold
• A38434 AIM: Power supply reactor winding temperature exceeded the alarm threshold
• A38807 AIM: Sequence control time monitoring
• A38903 AIM: I2C bus fault occurred
• A38904 AIM: EEPROM
• A38905 AIM: Parameter access
• A39200 IIoT: Communication problem
• A39801 IIoT: Heartbeat signal missing
• A39802 IIoT: Time slice overflow
• A39999 IIoT: Unknown alarm
• A40100 DRIVE-CLiQ slot X100 alarm
• A40101 DRIVE-CLiQ slot X101 alarm
• A40102 DRIVE-CLiQ slot X102 alarm
• A40103 DRIVE-CLiQ socket X103 alarm
• A40104 DRIVE-CLiQ slot X104 alarm
• A40105 DRIVE-CLiQ slot X105 alarm
• A42 Circuit board fault
• A44 Motor operation
• A45801 OM-AIO: Heartbeat signal missing
• A45802 OM-AIO: Time slice overflow
• A45999 OM-AIO: Unknown alarm
• A46801 OM-DIO: Heartbeat signal missing
• A46802 OM-DIO: Time slice overflow
• A46999 OM DIO: Unknown alarm
• A48605 SI: Checksum error
• A49170 Cooling unit: Alarm present
• A49171 Cooling unit: Thermal conductivity alarm threshold exceeded
• A49172 Cooling unit: Actual thermal conductivity value invalid
• A49173 Cooling unit: Coolant temperature alarm threshold exceeded
• A49201 Field summary signal alarm
• A49204 Field disabled alarm
• A49205 Field: Incorrect parameter settings for brushless field motor
• A49920 Main circuit protection switch has tripped
• A49921 Redundant main circuit protection switch has tripped
• A49922 24 V circuit protection switch has tripped
• A49926 Synchronization voltage protection switch has tripped
• A49927 Auxiliary fan circuit protection switch has tripped
• A49933 Field AC 230-V circuit protection switch has tripped
• A49934 Cooling unit AC 230 circuit protection switch has tripped
• A49935 Protection switch for the 24 V circuit of the power unit cabinet door magnet has tripped
• A49936 Lighting wiring/socket AC 230 V circuit protection switch has tripped
• A49937 USV not ready
• A49938 USV battery mode
• A49939 USV battery depleted
• A49940 Power unit AC 400V circuit protection switch has tripped
• A49941 The stop heating protection switch has tripped.
• A49942 SITOP circuit protection switch has tripped.
• A49998 Recorder trigger event occurred
• A5000 Warning: Power component thermal overload
• A50001 PROFINET configuration error
• A50002 Communication board: alarm 2
• A50003 Communication board: Warning 3
• A50004 Communication board: Warning 4
• A50005 Communication board: warning 5
• A50006 Communication board: warning 6
• A50007 Communication board: Warning 7
• A50008 Communication board: Warning 8
• A50010 PROFINET: Parameter setting consistency error
• A50011 EtherNetIP/ communication board: configuration error
• A50020 PROFINET: Second controller missing
• A501 Current limit
• A502 Overvoltage limit
• A503 Undervoltage limit
• A504 Converter overheat
• A505 Converter I2t
• A50513 FBLOCKS: Sequence value has been set
• A50514 FBLOCKS: Incorrect sampling time for the fixed execution cycle group
• A50517 FBLOCKS: Internal measurement currently valid
• A506 IGBT junction temperature rise alarm
• A507 Converter temperature signal loss
• A511 Motor overheat I2t
• A523 Output current fluctuation too high
• A52900 Data copy fault
• A52901 Braking resistor alarm threshold reached
• A52902 Emergency stop (EMGS) signal missing
• A52905 EPOS function is disabled
• A52932 PTO maximum limit: For incremental encoders, when the frequency of PTO exceeds 280K, the drive generates the A52932 alarm to indicate that the limit has been exceeded.
• A52961 Cavitation protection alarm
• A52962 MPC Run time out of range
• A52963 MPC PID Threshold exceeded
• A52964 MPC One motor available
• A52967 Advanced multipump control: Pump in maintenance status
• A52971 Flow confirmation fault
• A52975 Pump run warning
• A535 Braking resistor overload
• A541 Motor data identification active
• A600 RTOS overflow alarm
• A60003 Mains monitoring, auto restart activated
• A60018 "Digital output overloaded"
• A60032 "Motor temperature alarm"
• A60039 Alarm: I2t monitoring detected power unit overheat
• A60080 "Alarm
• A60081 "Alarm
• A60082 "Alarm derating factor K1
• A60098 "System utilization high"
• A60143 In braking mode, the field current setpoint starts to decrease when EMF is too high
• A60144 Field current setpoint lower limit reached
• A60165 Fan service life reached or exceeded
• A60166 Alarm: Fan speed too low
• A60169 "Fault device fan blocked"
• A60266 "Alarm fan not OK"
• A6310 Incorrect mains voltage (p29006) setting
• A7001 Connection between the electronic board and EEPROM on the A7009 backplane
• A7009 Backplane wiring damaged
• A7012 Motor temperature model 1/3 overheat
• A7092 Drive: Moment of inertia estimator not ready
• A7109 Fuse monitoring
• A7112 X23A
• A7118 XS1_1
• A7402 Drive: Minimum DC bus voltage controller activated).
• A7440 EPOS: Jerk time has reached the limit
• A7441 LR: Save the position offset for absolute encoder adjustment
• A7454 LR: No valid encoder for position value preprocessing
• A7455 EPOS: Maximum speed limited
• A7456 EPOS: Set speed limit
• A7457 EPOS: Incorrect input signal combination
• A7461 EPOS: Zero point not set
• A7462 EPOS: Selected traversing block number does not exist
• A7463 EPOS: External block change not requested in the traversing block
• A7465 EPOS: Traversing block has no subsequent block. No subsequent block exists in the traversing block. Alarm value (r2124, decimal): Missing
• A7467 EPOS: Traversing block contains invalid task parameters
• A7468 EPOS: Traversing block jump destination does not exist
• A7469 EPOS: Traversing block < target position < negative software limit switch
• A7470 EPOS: Traversing block > target position > forward software limit switch
• A7471 EPOS: Traversing block target position is outside the modulo range
• A7472 EPOS: Traversing block ABS_POS/ABS_NEG is not supported
• A7473 EPOS: Start of run range reached
• A7474 EPOS: End of run range reached
• A7477 EPOS: Target position < negative software limit switch
• A7478 EPOS: Target position > forward software limit switch
• A7479 EPOS: Negative software limit switch reached
• A7480 EPOS: Forward software limit switch reached
• A7483 EPOS: Travel to fixed stop: clamping torque not reached
• A7486 EPOS: Task to be suspended is missing
• A7487 EPOS: Run task cancellation missing
• A7496 EPOS: Cannot be enabled
• A7530 Drive: Drive data set DDS does not exist
• A7565 Drive: Encoder error at PROFIdrive encoder interface 1
• A7576 Encoderless operation activated due to a fault
• A7582 Error processing actual position value
• A7585 P-TRG or CLR activated
• A7588 Encoder 2: No valid encoder available for position value preprocessing. The pulse count parameter for encoder PTI is configured incorrectly. Restore the drive to factory settings and reconfigure the parameters.
• A7805 Power unit overload I2t
• A7910 "Motor overheat" alarm
• A7965 Saving required
• A7971 Commutation angle offset determination activated
• A7991 Motor data detection in progress
• A8511 PROFIdrive: Received configuration data invalid
• A8526 PROFIdrive: No cyclic connection
• A8565 PROFIdrive: Received configuration data invalid
• A8800 PROFIenergy Energy-saving mode activated
• A910 Vdc_max controller inhibited
• A911 Vdc_max controller active
• A912 Vdc_min controller active
• A921 Analog output parameters not set correctly
• A922 Converter has no load
• A923 Forward and reverse jogging requested simultaneously
• A930 Cavitation protection alarm
• A936 PID auto-tuning active
• A952 Load monitoring alarm
• F00001 Overcurrent – Motor power and converter power mismatch
• F00002 Overvoltage – Supply voltage too high or motor operating in generating mode
• F00003 Undervoltage – Power supply loss
• F00004 Converter overtemperature – Converter temperature exceeds the upper limit
• F00005 AC drive overload
• F0001 Overcurrent
• F0002 Overvoltage
• F0003 Undervoltage
• F0004 Converter overtemperature
• F00041 Motor parameter identification failure
• F0005 Converter I2T overtemperature
• F00052 Power module hardware data read failure
• F00062 MMC data invalid
• F00070 PLC setpoint fault
• F00071 USS setpoint fault
• F00072 USS setpoint fault
• F00090 Encoder feedback signal loss
• F001 Electronic board power supply fault during operation (5U1, 5W1
• F0011 Motor I2T overtemperature
• F0012 No inverter temperature signal
• F0015 No motor temperature signal
• F0020 Line supply phase missing
• F0021 Ground fault
• F0022 Hardware monitoring active
• F0023 Output fault
• F0024 Rectifier overtemperature
• F0030 Cooling fan fault
• F0035 Restart after n
• F004 Armature power supply phase fault (1U1, 1V1, 1W1
• F0040 Auto calibration fault
• F0041 Motor resistor auto detection
• F0042 Speed control optimization function
• F005 Field circuit fault
• F0051 Parameter EEPROM fault
• F0052 Power stack fault
• F0053 I/O EEPROM fault
• F0054 Incorrect I/O module
• F0055 BOP-EEPROM fault
• F0056 BOP is not installed in the converter
• F0057 BOP fault
• F0058 Information stored in BOP is incompatible
• F006 Undervoltage
• F0060 Asic timeout
• F007 Overvoltage
• F0070 CB setting value fault
• F0071 USS (BOP
• F0072 USS setpoint fault
• F008 Incoming power supply frequency is below the value specified by parameter
• F0080 ADC input signal
• F0085 External fault
• F009 Incoming frequency (armature and field power supply) exceeds 65 Hz
• F0090 Encoder signal loss
• F0100 Monitor (Watchdog) reset
• F01000 Internal software error
• F01001 Floating-point exception
• F01002 Internal software error
• F01003 Response delay during memory access
• F01005 Firmware download failure for component DRIVE-CLiQ
• F0101 Power component overflow
• F01010 Unknown drive type
• F01011 Download interruption
• F01012 Project conversion error
• F01014 Topology: DRIVE-CLiQ component properties changed
• F01015 Internal software error
• F01018 Multiple start interruptions
• F01022 BIOS upgrade required
• F01023 Internal software timeout
• F01029 Parameter mismatch between the DIP switch and 87 Hz mode
• F01030 Sign-of-life error under master control
• F01031 Sign-of-life error with "Remote mode off"
• F01033 Unit conversion: Reference parameter invalid
• F01034 Unit conversion: Parameter value calculation failure after reference value change
• F01036 ACX: Parameter backup file missing
• F01037 ACX: Parameter backup file rename failure
• F01038 ACX: Failure to load parameter backup file
• F01039 ACX: Failure to write the parameter backup file
• F01040 Parameter backup and power-on again required
• F01041 Parameter backup required
• F01042 Parameter error during project download
• F01043 A serious error occurred during project download
• F01044 CU: Description data error
• F01045 Configuration data invalid
• F01046 Parameter values from the project were not transferred
• F01047 Cannot restore drive data from the encrypted backup file
• F01050 Memory card is incompatible with the device
• F01051 Drive object type is not available
• F01054 CU: System limit exceeded
• F01055 CU: Internal error (application and port SYNO do not match
• F01056 CU: Internal error (parameter group clock cycle has already been assigned, but there is a deviation
• F01057 CU: Internal error (slave DRIVE-CLiQ types differ
• F01058 CU: Internal error (no slave in the topology
• F01059 CU: Internal error (port does not exist
• F01060 CU: Internal error (parameter group does not exist
• F01061 CU: Internal error (unknown application
• F01063 CU: Internal error (PDM
• F01068 CU: Data memory overflow
• F01070 Project/firmware download to the memory card in progress
• F01072 Restore the memory card from the backup file
• F01082 Parameter error in the data backup at start
• F01105 CU: Insufficient memory capacity
• F01106 CU: Insufficient memory capacity
• F01107 CU: Failure to save to memory card
• F01110 CU: More than one SINAMICS G on a single control unit
• F01111 CU: Mixed operation of drive units not permitted
• F01112 CU: Power unit not permitted
• F01120 Port initialization failure
• F01122 Frequency at the measuring probe input too high
• F01123 The power unit does not support digital inputs/outputs.
• F01150 CU: Number of instances of a drive object type exceeded
• F01151 CU: Number of drive objects in a category exceeded
• F01152 CU: Invalid drive object type
• F01200 CU: Internal software error in time slice management
• F01205 CU: Time slice overflow
• F01220 CU: Bas clk cyc too low
• F01221 CU: Base cycle too small
• F01222 CU: Basic clock cycle too small (no computation time available for communication
• F01250 CU: CU-EEPROM read-only data error
• F01255 CU: Read-only data error on plug-in board EEPROM
• F01257 CU: Firmware version too old
• F01260 The software has not yet been released.
• F01275 Hardware description error
• F01303 DRIVE-CLiQ Component does not support the requested function
• F01305 Topology: Component number missing
• F01325 Topology: Component number not included in the configured topology
• F01341 Topology: Maximum number of DRIVE-CLiQ components exceeded
• F01354 Topology: Incorrect component in actual topology
• F01355 Topology: Actual topology has changed
• F01356 Topology: Damaged DRIVE-CLiQ component present
• F01357 Topology: Two control units detected on branch DRIVE-CLiQ
• F01359 Topology: Insufficient DRIVE-CLiQ performance
• F01360 Topology: Invalid actual topology
• F01380 Topology: Damaged EEPROM in the actual topology
• F014 Parallel interface telegram fault
• F01451 Invalid configured topology
• F01470 Topology: Ring connection detected in the configured topology
• F01475 Topology: Duplicate connection between two components in the configured topology
• F015 Telegram fault on a SIMOLINK board
• F01505 BICO: Cannot establish connection
• F01506 BICO: No standard telegram
• F01507 BICO: Interconnections to inactive objects present
• F01510 BICO: Signal source is not floating-point
• F01511 BICO: Connection has different scaling
• F01512 BICO: No scaling
• F01513 BICO: Connections between different drive objects have different scaling
• F01515 BICO: Parameter write not permitted because master control is valid
• F01550 Network security: Drive data encryption invalid
• F01551 Network security: Integrity protection check failure
• F01560 Network security: Authenticity verification failure
• F01580 Network safety: hardware fault
• F01600 SI P1 (CU): STOP A triggered
• F01604 SI: Safety EEPROM data error
• F01606 SI: Safety hardware version error
• F01611 P1
• F01625 SI P1 (CU): Sign-of-life error in safety data
• F01630 "Incorrect safety brake control, P1"
• F01640 SI P1 (CU): Component replacement detected; acknowledgment/saving required
• F01641 SI P1 (CU): Component replacement detected; saving required
• F01646 SI: log change
• F01649 SI P1 (CU): Internal software error
• F01650 SI P1 (CU): Acceptance test required
• F01652 SI CU: Illegal monitoring clock cycle
• F01653 SI P1: PROFIBUS configuration error
• F01655 SI P1 (CU): Comparison of monitoring functions
• F01656 SI P1 (CU): Processor 2 parameter error
• F01658 SI P1 (CU): PROFIsafe telegram number is unsuitable
• F01659 Parameter write request rejected
• F01660 SI P1 (CU): Safety function not supported
• F01661 SI P1 (CU): Safety input simulation activated
• F01662 Internal communication fault
• F01663 SI P1 (CU): SI Parameter copying rejected
• F01664 SI P1 (CU): No auto firmware upgrade
• F01665 SI P1 (CU): System fault
• F01670 SI motion: Invalid encoder module parameter settings
• F01671 SI Motion: Parameterization error, encoder
• F01672 SI Motion: Motor Module software incompatible
• F01673 SI Motion: Sensor Module software incompatible
• F01674 SI Motion P1 (CU): PROFIsafe telegram does not support safety functions
• F01675 SI Motion P1: Setting in the PROFINET controller is not permitted
• F01679 SI CU: Safety parameters and topology have changed; warm restart/power-on required
• F01680 SI Motion P1 (CU): Safety monitoring checksum error
• F01681 SI motion P1 (CU): Incorrect parameter value
• F01682 SI motion P1 (CU): Monitoring function not supported
• F01683 SI Motion P1 (CU): Missing SLS enable
• F01684 SI Motion: Safely-Limited Position Limit values mixed up
• F01685 SI Motion: Safe velocity limit value too high
• F01686 SI Motion: Illegal parameterization, cam position
• F01687 SI Motion: Illegal parameterization, modulo value
• F01688 SI Motion: Actual value synchronization not permis
• F01689 SI Motion: Axis configuration changed
• F01690 SI motion: Data backup problem on NVRAM
• F01692 SI motion P1 (CU): Incorrect parameter value for operation without an encoder
• F01694 SI Motion CU: Motor module/hydraulic module firmware version is older than the control unit firmware version
• F01700 SI Motion P1 (CU): STOP A triggered
• F01701 SI motion P1 (CU): STOP B triggered
• F01708 SI Motion P1: Trigger SS2
• F01787 SBT Motor types differ
• F018 Digital output short circuit or overload
• F01800 DRIVE-CLiQ: Hardware/configuration error
• F01802 CU DRIVE-CLiQ: POWER ON due to basis sampling time
• F019 From free function blocks
• F01910 Fieldbus setpoint timeout
• F01911 PB/PN: Isochronous synchronization cycle fault
• F01912 PB/PN Sign-of-life error during isochronous synchronization
• F01913 COMM INT: Monitoring time, sign-of-life expired
• F01914 COMM INT: Monitoring time, configuration expired
• F01915 PB/PN: Drive object 1 isochronous synchronization sign-of-life error
• F01916 Internal communication error
• F01917 Internal communication error
• F01946 PROFIBUS: Connection interruption with publisher
• F01950 PB/PN: Isochronous synchronization failure
• F01951 CU SYNC: Synchronous application cycle missing
• F01952 CU DRIVE-CLiQ: Component synchronization not supported
• F01954 CU DRIVE-CLiQ: Synchronization unsuccessful
• F01978 CBE41: Overtemperature fault
• F02 Incorrect phase sequence (electronics board power supply 5U1, 5V1, 5W1
• F020 From free function blocks
• F02080 Trace: Parameter settings deleted due to unit conversion
• F02151 TEC: Internal software error
• F02152 TEC: Insufficient memory capacity
• F02153 TEC: Technology function does not exist
• F0221 PID feedback signal low
• F0222 PID feedback signal high
• F023 From free function blocks
• F024 From free function blocks
• F025 Carbon brushes too short
• F026 Poor bearing operating condition
• F027 Motor fan airflow monitoring
• F028 Motor overheat
• F030 Pulses blocked because the actual armature current is too high
• F03000 NVRAM error during operation
• F03001 NVRAM checksum error
• F031 Speed controller monitoring
• F033 From free function blocks
• F034 From free function blocks
• F035 Drive stalled
• F03500 TM: Initialization
• F03505 Analog input open
• F03590 TM: Module not ready
• F036 No armature current flowing
• F037 I2t Motor monitoring triggered
• F038 Overspeed
• F039 I2t Power unit monitoring response
• F0395 This fault, after hot-swapping CU/PM
• F04 Phase error; branch fuse blown.
• F040 The electronics board power supply is cut off while the fault status is active.
• F041 Parameter settings or ramp-function generator selection are ambiguous.
• F042 Tachogenerator fault
• F0422 No load applied to inverter
• F043 EMF too high during braking operation
• F044 One slave device connected to the parallel interface does not start operation.
• F0450 Failure BIST tests
• F0452 Load torque fault detected
• F0453 Motor stalled
• F046 Main reference
• F047 Configurable analog input
• F048 Fault in the measurement channel using a pulse encoder for digital speed detection
• F05 Supply voltage exceeded the permissible deviation range (+15/-20%).
• F050 Optimization run not possible
• F05050 Parallel circuit: Pulse enable reported despite pulses being inhibited
• F05051 Parallel circuit: Power unit pulse enable missing
• F05055 Parallel circuit: Invalid power unit code number
• F05056 Parallel circuit: Power unit EEPROM versions differ
• F05057 Parallel circuit: Power unit firmware versions differ
• F05058 Parallel circuit: VSM EEPROM versions differ
• F05059 Parallel circuit: VSM firmware versions differ
• F05060 Parallel circuit: Incompatible power unit firmware versions
• F05061 Number of infeed VSM units
• F05062 Parallel circuit: Different parallel connection versions of the power units
• F05064 Parallel operation: Pulse synchronization error
• F05068 Parallel circuit: AIM EEPROM versions differ
• F05069 Parallel circuit: AIM firmware versions differ
• F05118 Precharging contactor synchronization monitoring time exceeded
• F05119 Bypass contactor synchronization monitoring time exceeded
• F052 Optimization run interruption due to an external cause
• F053 From free function blocks
• F054 From free function blocks
• F055 No field characteristic curve recorded
• F056 Important parameters not set
• F058 Inconsistent parameter settings
• F06 Parity error in data received via the serial interface.
• F06000 Infeed: Precharging monitoring timeout
• F06010 Infeed: Power unit missing during operation EP 24 V
• F06050 Infeed: Smart mode not supported
• F06052 Infeed: Filter temperature detection not supported
• F06054 Infeed: Power unit modulation not supported
• F06080 Infeed: Parameter error
• F06081 Infeed: Power supply filter error
• F06100 Infeed: Tripped due to main power supply undervoltage
• F062 Parameter memory fault
• F06200 Infeed: One or more mains phase faults
• F06207 Infeed: Input current asymmetry
• F06210 Infeed: Total current too high
• F06211 Total current exceeded the permissible range
• F06255 Infeed: Temperature threshold not permitted
• F06261 Infeed: Input filter temperature persistently too high
• F06262 Infeed: Temperature switch in the input filter open at switch-on
• F06300 "Infeed: Line voltage too high at power on"
• F06310 Incorrect input voltage (p0210) parameter setting
• F06311 Infeed: Input voltage (p0210) fault
• F06320 Master/slave: 4 channel multiplexer control invalid
• F06321 Master/slave: 6 channel multiplexer control invalid
• F064 The watchdog timer has triggered a reset.
• F06410 Infeed: Smart identification error
• F065 Invalid microprocessor status
• F06500 "Infeed: Line synchronization not possible"
• F06503 Infeed: Mains black start failure
• F06504 Infeed: Islanded mains synchronization failure
• F06505 Infeed: Current limit exceeded during transformer field excitation
• F067 Rectifier cooling fault
• F06700 Infeed: Power supply contactor switched on under load
• F068 Analog detection channel fault
• F06850 Infeed: Short circuit time too long
• F06851 Infeed: Power supply monitoring of the distributed infeed has tripped
• F06855 fault value = 0
• F069 MLFB Data fault data fault
• F06906 Braking module internal fault information
• F06907 Braking module internal overheat
• F06908 Braking module internal overheat/trip
• F06909 Braking module internal Uce fault
• F06922 Braking resistor phase loss
• F07 Syntax error in data received via the serial interface.
• F070 SCB1: Severe initialization fault
• F07011 "Motor overtemperature"
• F07013 Drive: Motor temperature model configuration fault
• F07016 Drive: Motor temperature sensor fault message
• F07018 Additional temperature fault threshold exceeded
• F07048 Drive: Characteristic curve measurement error
• F07080 Drive: Closed-loop control parameter error
• F07082 Macro file: Cannot be executed
• F07083 Macro file: ACX file not found
• F07084 Macro file: Conditions for WaitUntil not met
• F07085 Drive: Open-loop/closed-loop control parameters changed
• F07086 Unit conversion: Parameter limits exceeded due to a change in the reference value
• F07087 Drive: Encoderless run is not possible at the set pulse frequency
• F07088 Unit conversion: Parameter limit exceeded due to unit conversion
• F07090 Drive: Torque upper limit is less than lower limit
• F07093 Drive: Test signal fault
• F07094 Common parameters out of range
• F07097 Drive: Test signal displacement limit error
• F07098 Drive: One-button optimization configuration error
• F07100 Drive: Sampling time cannot be reset
• F07110 Drive: Sampling time and basic cycle mismatch
• F07210 Master control PC/AOP inhibited
• F07217 PTI: Error inverting signal A/B/R
• F07220 Drive: Missing "Control via PLC"
• F07300 Drive: Missing power supply contactor feedback
• F07311 Motor bypass switch
• F07312 Power supply bypass switch
• F07320 Drive: Auto restart interruption
• F07330 Flying restart: Measured search current too small
• F07331 Flying restart: Function not supported
• F07332 Flying restart: Reduce maximum speed
• F07333 Control function not supported
• F07334 This function is not supported
• F07335 Drive: Parameter changes require recalculation of controller data
• F07355 Drive configuration: Cogging torque compensation: Error during teach-in
• F07390 Error during DC bus capacitor reforming
• F07403 Drive: Lower DC bus voltage threshold reached
• F07404 Drive: DC bus voltage threshold upper limit
• F07405 Drive: Speed below the minimum speed for kinetic buffering
• F07406 Drive: Maximum duration in kinetic buffering status exceeded
• F07407 Drive: Vdc reduction not permitted
• F07410 Drive: Current loop output limited
• F07411 Drive: Flux setpoint not reached during field excitation
• F07412 Drive: Commutation angle error (motor model
• F07413 Commutation angle error (magnetic pole position detection
• F07417 Drive pulse method implausible (motor model
• F07419 Drive: Current setpoint filter adaptation error
• F07420 Drive: Current setpoint filter natural frequency > Shannon frequency
• F07421 Drive: Speed filter natural frequency > Shannon frequency
• F07422 Drive: Reference model natural frequency > Shannon frequency
• F07423 Drive: APC filter natural frequency > Shannon frequency
• F07425 Drive: APC speed limit monitoring time exceeded
• F07426 Technology controller actual value reached the limit
• F07429 Drive: DSC is not supported without an encoder
• F07430 Drive: Cannot switch to open-loop torque operation
• F07431 Drive: Cannot switch to encoderless run
• F07432 Drive: Motor has no overvoltage protection
• F07433 Drive: Cannot switch to run with encoder because the encoder has not been unparked
• F07434 Drive: Cannot change the direction of rotation while pulses are enabled
• F07435 Drive: Incorrect ramp-function generator setting in encoderless vector control
• F07436 Free Tec_reg 0 actual value has reached the limit
• F07437 Free Tec_reg 1 actual value has reached the limit
• F07438 Free Tec_reg 2 actual value has reached the limit
• F07439 Drive: Higher current loop dynamic response not permitted
• F07442 Position loop: Multi-turn resolution and modulo range mismatch
• F07443 Position loop: Reference point coordinate exceeded the permissible range
• F07445 PID Auto tuning interruption
• F07446 Load gearbox: Position tracking cannot be reset
• F07447 Load gearbox: Position tracking exceeded the maximum actual value
• F07448 Load gearbox: Linear axis position tracking exceeded the maximum range
• F07449 Load gearbox: Current position is outside the position tracking tolerance range
• F07450 Position loop: Static monitoring has triggered
• F07451 Position loop: Positioning monitoring triggered
• F07452 Position loop: Following error too large
• F07453 Position loop: Error in actual position value processing
• F07458 EPOS: Reference point cam not found
• F07459 EPOS: Zero pulse missing
• F07460 EPOS: End of reference point cam not found
• F07464 EPOS: Traversing block mismatch
• F07475 EPOS: Target position < start of travel range
• F07476 EPOS: Target position > end of travel range
• F07481 EPOS: Axis position < negative software limit switch
• F07482 EPOS: Axis position > positive software limit switch
• F07484 EPOS: Fixed stop outside the monitoring window
• F07485 EPOS: Fixed stop not reached
• F07488 EPOS: Cannot perform relative positioning
• F07490 EPOS: Enable withdrawn during operation
• F07491 EPOS: Negative stop cam reached
• F07492 EPOS: Positive stop cam reached
• F07493 Position loop: Actual position value range overflow
• F07494 Position loop: Drive data set switched during operation
• F07499 EPOS: Reversing cam reached in the wrong direction
• F07500 Drive: Power unit data set PDS not defined
• F07501 Drive: Motor data set MDS not defined
• F07502 Drive: Encoder data set EDS not defined
• F07503 EPOS: Approaching the stop cam in the wrong direction of travel
• F07509 Drive: Component assignment missing
• F07510 Drive: Identical encoders in the drive data set
• F07511 Drive: Encoder used multiple times
• F07512 Drive: Cannot set encoder data set changeover parameters
• F07515 Drive: Incorrect connection between power unit and motor
• F07516 Drive: Recommission data set
• F07517 Drive: Incorrect encoder data set changeover parameter setting
• F07518 Drive: Incorrect parameter settings for motor data set changeover
• F07545 Drive: WSG interface setting error
• F07551 Drive encoder: No commutation angle information
• F07552 Drive encoder: Encoder configuration not supported
• F07553 Drive encoder: Encoder module configuration not supported
• F07555 Drive encoder: Position tracking configuration
• F07556 Measuring gearbox: Position tracking exceeded the maximum actual value
• F07560 Drive encoder: Line count is not a power of two
• F07561 Drive encoder: Multi-turn line count is not a power of two
• F07562 Drive encoder: Position tracking cannot be performed with the incremental encoder
• F07563 Drive encoder: XIST1_ERW configuration error
• F07575 Drive: Motor encoder not ready
• F07599 Encoder 1: Cannot perform calibration
• F07600 Encoder 2: Cannot perform calibration
• F07601 Encoder 3: Calibration cannot be performed
• F07750 Drive: Invalid parameter
• F07751 Drive: Valve does not respond
• F07752 Drive: Incorrect piston position
• F07753 Drive: No valid actual pressure value
• F07754 Drive: Shutoff valve configuration error
• F07800 Drive: No power unit
• F07801 Drive: Motor overcurrent
• F07802 Drive: Infeed or power unit not ready
• F07806 Regenerative power limit exceeded
• F07807 Drive: Short circuit/ground fault detected
• F07808 HF damper: Damping not ready
• F07810 Drive: No rated data for power unit EEPROM
• F07815 Drive: Power unit modified
• F07822 Speed below the insufficient speed threshold: monitoring fault
• F07824 I2t monitoring fault threshold exceeded
• F07826 Drive: DC bus voltage too high during simulated operation
• F07840 Drive: Infeed run missing
• F07841 Drive: Infeed operation canceled
• F07860 External fault 1
• F07861 External fault 2
• F07862 External fault 3
• F07890 Internal voltage protection/internal armature short circuit and STO active
• F07894 Drive: Pump/fan stall monitoring
• F07895 Drive: Pump/fan no-load monitoring
• F07896 Drive: Pump leakage monitoring
• F07898 Drive: Flying restart failure due to flux too low
• F079 SCB1: Telegram fault telegram fault
• F07900 Drive: Motor stalled
• F07901 Drive: Motor speed too high
• F07902 Drive: Motor pull-out detection
• F07904 External armature short circuit: Contactor feedback "closed" missing
• F07905 External armature short circuit: Missing contactor feed
• F07906 Armature short circuit/internal voltage protection: Incorrect parameter setting
• F07907 Internal armature short circuit: Motor terminal potentials are no longer isolated after pulse suppression
• F07909 Internal voltage protection: Failure only after power-on
• F07913 Field current out of tolerance
• F07914 Magnetic flux out of tolerance
• F07923 Drive: Torque/speed too small
• F07924 Drive: Torque/speed too large
• F07925 Tolerance exceeded for torque/speed
• F07928 Internal voltage protection triggered
• F07930 Drive: Braking control error
• F07933 Drive: Braking voltage error
• F07934 Drive: S120 Combi motor holding brake configuration
• F07935 Drive: Motor holding brake detected
• F07936 Drive: Loading fault
• F07937 Drive: Speed deviation between motor model and external speed
• F07940 Sync-line supply - drive: Synchronization error
• F07950 Motor parameter error
• F07951 Drive: Motor error
• F07955 Drive: Motor has been changed
• F07956 Drive: Motor code mismatch with motor list
• F07963 "Friction characteristic record
• F07966 Drive: Check commutation angle
• F07967 Drive: Magnetic pole position detection error
• F07968 Drive: Lq-Ld measurement error
• F07969 Drive: Magnetic pole position detection error
• F07970 Converter: Error during encoder auto zeroing
• F07977 EOM and Safety Integrated (SI are not supported
• F07982 Drive: Encoder test for rotation detection
• F07983 Drive: Saturation characteristic curve for rotation detection
• F07985 Drive: Speed loop optimization (oscillation test
• F07986 Drive: Rotation detection, ramp function generator error
• F07988 Drive: No configuration selected for rotation detection
• F07989 Drive: Rotation detection, leakage inductance error (q direction)
• F07990 Drive: Motor data detection error
• F07993 Drive: Error in rotating field direction or encoder actual value reversal
• F07995 Drive: Magnetic pole position detection failure
• F07996 Drive: Magnetic pole position detection not performed
• F08 Framing error in data received via the serial interface.
• F08000 TB: Power supply +/-15 V error
• F08010 TB: Analog-to-digital converter
• F081 CB/TB Core clock error
• F08500 COMM BOARD: Configuration monitoring time expired
• F08501 PN/COMM BOARD: Setpoint timeout
• F08502 PN/COMM BOARD: Sign-of-life monitoring time expired
• F08510 PN/COMM BOARD: Invalid send configuration data
• F08700 CAN: Communication fault
• F08701 CAN: NMT status transition
• F08702 CAN: RPDO timeout
• F08703 CAN: Maximum number of drive objects exceeded
• F09 Overflow error in data received via the serial interface.
• F0952 Function diagram number
• F0999 Converter initialization fault
• F1 Overcurrent
• F10 Overspeed signal
• F100 Watchdog reset
• F1000 Internal software error
• F1001 Floating-point error
• F1002 Internal software error
• F1003 Response delay during memory access
• F101 Stack overflow
• F1015 Internal software error
• F1018 Multiple start interruptions
• F1030 Host computer communication fault
• F11 Tachogenerator fault (analog tachogenerator) or armature circuit interruption
• F12 Actual current > 300% of the rated rectifier current
• F13 I2t monitoring triggered (motor too hot
• F13000 Insufficient license
• F13009 Technology extension module license not authorized
• F13010 Function module license not granted
• F13020 Insufficient licenses in the control system
• F13100 Know-how protection: Copy protection fault
• F13101 Know-how protection: Copy protection cannot be activated
• F13102 Know-how protection: Consistency error in protected data
• F14 External fault
• F147 This group of fault messages is activated through the option board.
• F15 Speed controller monitoring
• F16 Motor stalled in the drive system
• F1611 SICU: Fault detected
• F18 The drive system does not reach rated speed despite maximum field weakening.
• F19 Armature current cannot flow.
• F1910 Fieldbus: Setpoint timeout
• F1911 PROFIdrive: Isochronous cycle fault
• F1912 PROFIdrive: Clock cycle synchronization operation failure
• F2 Overvoltage
• F20 Electronics board power supply fault (5U1, 5V1, 5W1
• F200 Script error
• F221 PID feedback signal below minimum
• F222 PID feedback signal above maximum
• F23 Example
• F24 Fault in the measurement channel for the digital speed read from the pulse encoder or the interrupted armature circuit.
• F25 Fault in the armature voltage measurement circuit or the analog input signal measurement circuit.
• F26 Armature current cannot decrease during torque reversal; electromotive force is too high.
• F27 USS telegram fault at G-SST1
• F28 FIF0 overflow
• F29 Parameter value exceeded the permitted range
• F29001 Infeed: Power unit overcurrent
• F29002 Infeed: Power unit DC bus overvoltage
• F29004 "Heat sink overtemperature"
• F29005 Infeed: Power unit I2t overload
• F29007 Infeed: Power unit positive/negative DC bus imbalance
• F29008 Infeed: Power unit cyclic data heartbeat signal error
• F29011 Infeed: Power unit mains imbalance
• F29012 Infeed: Power unit temperature sensor open
• F29017 Infeed: Power unit hardware current limit activated too frequently
• F29018 Infeed: Incorrect IHD card inserted in the power unit
• F29020 Infeed: Power unit does not support this configuration
• F29022 Infeed: Power unit U_ce monitoring
• F29024 "Overtemperature thermal model"
• F29025 "Chip overtemperature"
• F29035 Infeed: Power unit inlet air overheat
• F29036 Infeed: Power unit internal compartment overheat
• F29040 Infeed: Power unit 24 V undervoltage
• F29043 Infeed: Power unit 24/48 V overvoltage
• F29045 Infeed: Power unit power supply undervoltage
• F29050 Infeed: Power unit 24V power supply overvoltage
• F29052 Infeed: EEPROM data error
• F29053 Infeed: FPGA data error
• F29055 Infeed: Power unit braking module overcurrent
• F29059 Infeed: Power unit auxiliary fan 1 damaged
• F29062 Infeed: Bypass contactor open while energized
• F29067 Infeed: Power unit capacitor air outlet overheat fault
• F29068 Infeed: Power unit inverter heatsink undertemperature
• F29081 Infeed: Power unit switching operations too frequent
• F29087 Infeed: Power unit coolant temperature exceeded the fault threshold
• F29088 Infeed: Power unit sub-DC bus overvoltage
• F29097 Infeed: Balancing resistor thermal overload
• F29105 Infeed: Power unit actual value acquisition error
• F29260 Infeed: Power supply fault in the power unit's power semiconductor drive circuit
• F29261 Infeed: Power unit auxiliary fan 2 damaged
• F29802 Infeed: Power unit time slice overflow
• F29804 Infeed: power unit CRC
• F29805 Infeed: Power unit EEPROM checksum incorrect
• F29809 Infeed: Power unit switching information invalid
• F29810 Infeed power unit: Watchdog timer timeout
• F29815 Power unit: Processor clock signal error
• F29820 Infeed: Power unit DRIVE-CLiQ telegram error
• F29836 Infeed: Power unit DRIVE-CLiQ: DRIVE-CLiQ data transmission error
• F29837 Infeed: Power unit DRIVE-CLiQ component fault
• F29845 Infeed: Power unit DRIVE-CLiQ cyclic data transmission error
• F29850 Infeed: Internal power unit software error
• F29851 Power unit DRIVE-CLiQ: Heartbeat signal fault
• F29860 Infeed: Power unit DRIVE-CLiQ (CU) telegram error
• F29903 Infeed: Power unit I2C bus fault
• F29907 Infeed: Power unit FPGA configuration failure
• F29950 Infeed: Internal power unit software error
• F3 Undervoltage
• F30 Fault during plotting of the field characteristic curve
• F30001 Overcurrent
• F30002 DC bus overvoltage
• F30003 Power unit: DC bus undervoltage
• F30004 Power unit: Inverter heatsink overheat
• F30005 Power unit: I2t overload
• F30006 Power unit: SCR control board
• F30008 Power unit: Cyclic data sign-of-life error
• F30011 Power unit: Phase loss in the main circuit
• F30012 Power unit: Heatsink temperature sensor open
• F30013 Power unit: Heatsink temperature sensor short circuit
• F30015 Power unit: Phase loss in motor supply cable
• F30017 Power unit: Hardware current limit responds too frequently
• F30021 Ground fault
• F30022 Power module: monitoring UCE
• F30024 Power unit: Thermal model overheat
• F30025 Power unit: Chip overheat
• F30026 Power unit: DC bus precharging imbalance
• F30027 Power unit: DC bus precharging time monitoring
• F30035 Power unit: Air inlet overheat
• F30036 Power unit: internal space overheat
• F30037 Power unit: Rectifier overheat
• F30039 Power unit: Capacitor fan fault
• F30040 Power unit: 24/48 V undervoltage
• F30043 Power unit: 24/48 V overvoltage
• F30045 Power unit: Power supply undervoltage
• F30047 Cooling unit: Coolant volumetric flow rate too low
• F30050 Power unit: 24V power supply overvoltage
• F30051 Power unit: Motor holding brake short circuit detected
• F30052 EEPROM data error
• F30053 FPGA data error
• F30055 Power unit: Braking chopper overcurrent
• F30058 Power unit: Heatsink fan damaged
• F30059 Power unit: Internal fan damaged
• F30060 Precharging contactor status monitoring
• F30061 Bypass contactor status monitoring
• F30062 Bypass contactor open while energized
• F30067 Power unit: Capacitor air outlet overheat fault
• F30068 Power unit: Inverter heatsink undertemperature
• F30070 Power unit does not support the requested cycle
• F30071 Power unit has not received a new actual value
• F30072 Setpoints can no longer be transmitted to the power unit
• F30074 Communication fault between the control unit and the power module
• F30075 Power unit configuration failure
• F30078 Power unit: Fan damaged or power supply reactor overheat
• F30080 Power unit: Current rising too quickly
• F30081 Power unit: Switching operations too frequent
• F30083 Power unit: Coolant volumetric flow rate too low; fault threshold exceeded
• F30087 Power unit: Coolant temperature exceeded the fault threshold
• F30088 Power unit: Sub-DC bus overvoltage
• F30097 Power unit: thermal overload of the balancing resistor
• F30105 Power unit: Actual value acquisition error
• F30258 Power unit: I2t overload (DC
• F30260 Power unit: Power supply fault in the power semiconductor drive circuit
• F30261 Power unit: Auxiliary fan 2 damaged
• F30262 Power unit: Braking module damaged
• F30263 Power unit: Top braking module damaged
• F30264 Power unit: Braking module disabled due to implausible DC bus voltage
• F30265 Power unit: Power supply power loss detected
• F30268 Power unit: Active power overload
• F30314 Power unit: 24 V power supply overloaded by PM
• F30524 SI: Safety EEPROM data error
• F30526 SI: Incorrect safety hardware version of the motor module
• F30600 SI P2: STOP A triggered
• F30604 SI: Safety EEPROM data error
• F30606 SI: Incorrect safety hardware version of the motor module
• F30611 P2
• F30625 SI P2: Sign-of-life error in safety data
• F30630 "Incorrect safety brake control, P2"
• F30640 SI MM: Fault in the control shutdown path
• F30649 SI P2: Internal software error
• F30650 SI P2: Acceptance test required
• F30651 SI P2: Synchronization with the control unit failed
• F30655 SI P2: Monitoring function comparison
• F30656 SI P2: Processor 2 parameter error
• F30657 SI P2: PROFIsafe telegram number invalid
• F30659 SI P2: Parameter write job rejected
• F30662 Internal communication fault
• F30664 Fault during start
• F30665 SI P2: System fault
• F30672 SI P2: Control unit software incompatible
• F30674 SI Motion P2: PROFIsafe telegram does not support safety functions
• F30680 SI Motion P2: Safety monitoring checksum error
• F30681 SI Motion P2: Parameter value error
• F30682 SI Motion P2: Monitoring function not supported
• F30683 SI motion P2: SLS enable missing
• F30684 SI Motion P2: Safely-Limited Position limit values mixed up
• F30685 SI motion P2: Safely limited speed limit value too large
• F30686 SI motion: Incorrect cam position parameter setting
• F30688 SI motion MM: Actual value synchronization error
• F30692 SI Motion P2: Parameter value error without encoder
• F30700 SI Motion P2: STOP A triggered
• F30701 SI motion P2: STOP B triggered
• F30708 SI motion P2: SS2 triggered
• F30770 SI motion P2: Discrepancy error in fail-safe inputs
• F30801 Power unit DRIVE-CLiQ: Sign-of-life fault
• F30802 Power unit: Time slice overflow
• F30804 Power unit: CRC
• F30805 Power unit: EEPROM checksum incorrect
• F30809 Power unit: Invalid switching information
• F30810 Power unit: Watchdog timer timeout
• F30815 Power unit: Processor clock signal error
• F30820 Power unit DRIVE-CLiQ: Telegram fault
• F30835 Power unit DRIVE-CLiQ: Cyclic data transfer fault
• F30836 Power unit DRIVE-CLiQ: DRIVE-CLiQ data transmission error
• F30837 Power unit DRIVE-CLiQ: Component fault
• F30845 Power unit DRIVE-CLiQ: Cyclic data transfer fault
• F30850 Power unit: Internal software error
• F30851 Power unit DRIVE-CLiQ (CU): Sign-of-life fault
• F30860 Power unit DRIVE-CLiQ (CU): Telegram fault
• F30885 Power unit CU DRIVE-CLiQ(CU): Cyclic data transfer fault
• F30886 Power unit DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F30887 Power unit DRIVE-CLiQ(CU): Component fault
• F30895 Power unit DRIVE-CLiQ(CU): Fault in interactive cyclic data transfer
• F30896 Power unit DRIVE-CLiQ(CU): Component characteristic mismatch
• F30897 DRIVE-CLiQ: No communication to component
• F30899 Power unit: Unknown fault
• F30903 Power unit: I2C bus fault
• F30907 Power unit: FPGA configuration failure
• F30950 Power unit: Internal software error
• F31 The transition from discontinuous to continuous armature current is set above the rated motor current via P71.
• F31100 Encoder 1: Zero pulse spacing error
• F31101 Encoder 1: Zero pulse fault
• F31103 Encoder 1: Signal R amplitude error
• F31110 Serial communication fault
• F31111 Motor encoder: Encoder reports an internal error (details
• F31112 Motor encoder: Encoder reports an internal error
• F31115 Encoder 1: Signal A or B amplitude error (A^2 + B^2
• F31116 Encoder 1: Monitoring signal A + B amplitude error
• F31117 Encoder 1: Signal A/B/R inversion error
• F31118 Encoder 1: Speed difference exceeded tolerance
• F31120 Encoder 1: Supply voltage fault
• F31121 Encoder 1: Coarse position error
• F31122 Encoder 1: Encoder module hardware error
• F31123 Encoder 1: Signal level A/B exceeded tolerance
• F31125 Encoder 1: Signal A or B level too large
• F31126 Encoder 1: AB amplitude too high
• F31129 Encoder 1: Position difference between Hall sensor/signal C/D and signal A/B too large
• F31130 Encoder 1: Zero pulse and position error during coarse synchronization
• F31131 Encoder 1: Incremental/absolute position offset too large
• F31137 Encoder 1: Internal positioning error
• F31138 Encoder 1: Internal error when determining multi-turn information
• F31142 Encoder 1: Battery voltage fault
• F31150 Encoder 1: Initialization failure
• F31151 Encoder 1: Encoder speed too high during initialization
• F31152 Encoder 1: Maximum signal frequency exceeded (signal A/B
• F31153 Encoder 1: Identification failure
• F31160 Encoder 1: Analog encoder channel A fault
• F31161 Encoder 1: Analog encoder channel B fault
• F31163 Encoder 1: Analog sensor position value exceeds the limit
• F31405 Encoder 1: Encoder detection temperature exceeded
• F31500 Encoder 1: Position tracking operating range exceeded
• F31501 Encoder 1: Encoder position outside the tolerance range for position tracking
• F31502 Encoder 1: No valid signal from encoder with measuring gearbox
• F31503 Encoder 1: Cannot reset position tracking
• F31801 Encoder 1 DRIVE-CLiQ: Sign of life missing
• F31802 Encoder 1: Time slice overflow
• F31804 Encoder 1: Checksum error
• F31805 Encoder 1: EPROM checksum incorrect
• F31806 Encoder 1: Initialization error
• F31811 Encoder 1: Encoder serial number changed
• F31812 Encoder 1: Requested cycle or RX/TX timing not supported
• F31813 Encoder 1: Hardware logic unit fault
• F31820 Encoder 1 DRIVE-CLiQ: Telegram fault
• F31835 Encoder 1 DRIVE-CLiQ: Cyclic data transfer fault
• F31836 Encoder 1 DRIVE-CLiQ: DRIVE-CLiQ data send error
• F31837 Encoder 1 DRIVE-CLiQ: Component fault
• F31845 Encoder 1 DRIVE-CLiQ: Cyclic data transfer error
• F31850 Encoder 1: Internal software error in encoder evaluation
• F31851 CU DRIVE-CLiQ: Sign-of-life missing
• F31860 CU DRIVE-CLiQ: Telegram error
• F31885 Encoder 1 DRIVE-CLiQ: Cyclic data transfer fault
• F31886 Encoder 1 DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F31887 CU DRIVE-CLiQ: Component fault
• F31895 Encoder 1 DRIVE-CLiQ(CU): Cyclic data exchange fault
• F31896 Encoder 1 DRIVE-CLiQ(CU): Component characteristics mismatch
• F31897 DRIVE-CLiQ: No communication to component
• F31899 Encoder 1: Unknown fault
• F31905 Encoder 1: Encoder parameter setting error
• F31912 Encoder 1: Device combination not permitted
• F31916 Encoder 1: Parameter setting error
• F31950 Encoder 1: Internal software error
• F32 Optimization run: Residual magnetism too high
• F32100 Encoder 2: Zero pulse spacing error
• F32101 Encoder 2: Zero pulse fault
• F32103 Encoder 2: Signal R amplitude error
• F32110 Serial communication fault
• F32112 Encoder 2: Fault bit set in the serial record
• F32115 Encoder 2: Amplitude error track A or B (A^2 + B^2
• F32116 Encoder 2: Monitoring signal A + B amplitude error
• F32117 Encoder 2: Signal A/B/R inversion error
• F32118 Encoder 2: Speed difference tolerance exceeded
• F32120 Encoder 2: Supply voltage fault
• F32121 Encoder 2: Measured commutation position error
• F32122 Encoder 2: Encoder module hardware error
• F32123 Encoder 2: Signal level A/B out of tolerance
• F32125 Encoder 2: Overmodulated signal A or B amplitude error
• F32126 Encoder 2: AB amplitude too high
• F32129 Encoder 2: Position difference between Hall sensor/signal C/D and signal A/B too large
• F32130 Encoder 2: Zero pulse and position error during coarse synchronization
• F32131 Encoder 2: Incremental/absolute position offset too large
• F32137 Encoder 2: Internal positioning error
• F32138 Encoder 2: Internal error when determining multi-turn information
• F32142 Encoder 2: Battery voltage fault
• F32150 Encoder 2: Initialization failure
• F32151 Encoder 2: Encoder speed too high during initialization
• F32152 Encoder 2: Maximum signal frequency exceeded (signal A/B
• F32153 Encoder 2: Identification failure
• F32160 Encoder 2: Analog encoder channel A fault
• F32161 Encoder 2: Analog encoder channel B fault
• F32163 Encoder 2: Analog sensor position value exceeds limit
• F32405 Encoder 2: Temperature detection limit exceeded
• F32500 Encoder 2: Position tracking operating range exceeded
• F32501 Encoder 2: Encoder position outside tolerance range for position tracking
• F32502 Encoder 2: No valid signal from encoder with measuring gearbox
• F32503 Encoder 2: Cannot reset position tracking
• F32801 Encoder 2 DRIVE-CLiQ: Sign-of-life signal missing
• F32802 Encoder 2: Time slice overflow
• F32804 Encoder 2: CRC CODE RAM
• F32805 Encoder 2: EEPROM checksum incorrect
• F32806 Encoder 2: Initialization error
• F32811 Encoder 2: Encoder serial number changed
• F32812 Encoder 2: Requested clock cycle or RX/TX timing not supported
• F32813 Encoder 2: Hardware logic unit fault
• F32820 Encoder 2 DRIVE-CLiQ: Telegram fault
• F32835 Encoder 2 DRIVE-CLiQ: Cyclic data transfer error
• F32836 Encoder 2 DRIVE-CLiQ: Send error for DRIVE-CLiQ da
• F32837 Encoder 2 DRIVE-CLiQ: Component fault
• F32845 Encoder 2 DRIVE-CLiQ: Cyclic data transfer error
• F32850 Encoder 2: Internal software error in encoder evaluation
• F32851 CU DRIVE-CLiQ: Sign-of-life missing
• F32860 CU DRIVE-CLiQ: Telegram error
• F32887 CU DRIVE-CLiQ: Component fault
• F32895 Encoder 2 DRIVE-CLiQ(CU): Cyclic data exchange fault
• F32896 Encoder 2 DRIVE-CLiQ(CU): Component characteristics mismatch
• F32897 DRIVE-CLiQ: No communication to component
• F32899 Encoder 2: Unknown fault
• F32905 Encoder 2: Encoder parameter setting error
• F32912 Encoder 2: Device combination not permitted
• F32916 Encoder 2: Parameter setting error
• F32950 Encoder 2: Internal software error
• F33100 Encoder 3: Zero pulse spacing error
• F33101 Encoder 3: Zero pulse fault
• F33111 Encoder 3: Absolute encoder EnDat, internal fault/
• F33112 Encoder 3: The error bit is set in the serial prot
• F33115 Encoder 3: Amplitude error track A or B (A^2 + B^2
• F33118 Encoder 3: Speed difference outside the tolerance
• F33120 Encoder 3: Power supply voltage
• F33121 Encoder 3: Measured commutation position error
• F33122 Encoder 3: Encoder module hardware error
• F33123 Encoder 3: Signal level A/B outside tolerance
• F33125 Encoder 3: Signal A or B level too large
• F33126 Encoder 3: Signal A or B level too large
• F33142 Encoder 3: Battery voltage fault
• F33150 Encoder 3: Initialization failure
• F33151 Encoder 3: Encoder speed too high during initialization
• F33152 Encoder 3: Maximum input frequency exceeded
• F33153 Encoder 3: Identification failure
• F33160 Encoder 3: Analog encoder channel A fault
• F33161 Encoder 3: Analog encoder channel B fault
• F33163 Encoder 3: Analog sensor position value exceeded the limit
• F33405 Encoder 3: Encoder detection temperature exceeded
• F33500 Encoder 3: Position tracking operating range exceeded
• F33501 Encoder 3: Encoder position for position tracking outside tolerance range
• F33502 Encoder 3: No valid signal from encoder with measuring gearbox
• F33503 Encoder 3: Cannot reset position tracking
• F33801 Encoder 3 DRIVE-CLiQ: Sign-of-life signal missing
• F33802 Encoder 3: Time slice overflow
• F33804 Encoder 3: Checksum error
• F33805 Encoder 3: EPROM checksum error
• F33806 Encoder 3: Initialization error
• F33812 Encoder 3: Requested cycle or RX/TX timing not supported
• F33813 Encoder 3: Hardware logic unit fault
• F33820 Encoder 3 DRIVE-CLiQ: Telegram error
• F33835 Encoder 3 DRIVE-CLiQ: Cyclic data transfer error
• F33836 Encoder 3 DRIVE-CLiQ: DRIVE-CLiQ data transmission error
• F33837 Encoder 3 DRIVE-CLiQ: Component fault
• F33845 Encoder 3 DRIVE-CLiQ: Cyclic data transfer error
• F33850 Encoder 3: Sensor Module, internal software error
• F33851 CU DRIVE-CLiQ: Sign-of-life missing
• F33860 CU DRIVE-CLiQ: Telegram error
• F33875 Encoder 3: Supply voltage fault
• F33887 Encoder 3 DRIVE-CLiQ(CU): Component fault
• F33895 Encoder 3 DRIVE-CLiQ(CU): Cyclic data exchange fault
• F33896 Encoder 3 DRIVE-CLiQ(CU): Component characteristics mismatch
• F33897 DRIVE-CLiQ: No communication to component
• F33899 Encoder 3: Unknown fault
• F33905 Encoder 3: Incorrect encoder parameter setting
• F33912 Encoder 3: Device combination not permitted
• F33916 Encoder 3: Incorrect encoder parameter setting
• F33950 Encoder 3: Internal software error
• F34 EEPROM fault) can be inhibited by setting parameter P87=x1 or x2
• F34207 VSM: Temperature fault threshold exceeded
• F34801 VSM DRIVE-CLiQ: Sign-of-life missing
• F34802 VSM: Time slice overflow
• F34803 VSM: Memory test
• F34804 VSM: CRC
• F34805 VSM: EEPROM checksum incorrect
• F34806 VSM: Initialization
• F34820 VSM DRIVE-CLiQ: Telegram fault
• F34835 VSM DRIVE-CLiQ: Cyclic data transfer error
• F34836 VSM DRIVE-CLiQ: DRIVE-CLiQ data send error
• F34837 VSM DRIVE-CLiQ: Component fault
• F34850 VSM: Internal software error
• F34851 VSM DRIVE-CLiQ (CU): Sign-of-life signal missing
• F34860 VSM DRIVE-CLiQ (CU): Telegram fault
• F34875 VSM DRIVE-CLiQ (CU): Supply voltage fault
• F34885 VSM DRIVE-CLiQ (CU): Cyclic data transfer fault
• F34886 VSM DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F34887 VSM DRIVE-CLiQ (CU): Component fault
• F34895 VSM DRIVE-CLiQ(CU): Interactive cyclic data transfer fault
• F34896 VSM DRIVE-CLiQ(CU): Component characteristic mismatch
• F34897 DRIVE-CLiQ: No communication to component
• F34899 VSM: Unknown fault
• F34920 VSM: Overtemperature or temperature sensor fault
• F34950 VSM: Internal software error
• F35 Fault during field weakening operation
• F350 Converter configuration vector fault
• F35000 TM54F: Invalid sampling time
• F35002 TM54F: Commissioning mode rejected
• F35003 TM54F: Acknowledgment required on the control unit
• F35004 TM54F: Invalid communication cycle
• F35005 TM54F: Parallel connection not supported
• F35006 TM54F: Invalid drive group
• F35009 TM54F: Drive safety commissioning incomplete
• F35011 TM54F: Drive object number assignment error
• F35013 TM54F: Error during forced fault check
• F35040 TM54F: 24 V undervoltage
• F35043 TM54F: 24 V overvoltage
• F35051 TM54F: Fault in one monitoring channel
• F35150 TM54F: Communication fault
• F35151 "Discrepancy
• F35207 Channel 0
• F35208 Channel 1
• F35209 Channel 2
• F35210 Channel 3
• F35220 TM: Frequency limit reached for signal output
• F35221 "Setpoint-actual value deviation outside
• F35229 TM: Time slice disabled
• F35230 TM: Hardware fault
• F35233 DRIVE-CLiQ component does not support the function
• F35400 Channel 4
• F35401 Channel 5
• F35402 Channel 6
• F35403 Channel 7
• F35404 Channel 8
• F35405 Channel 9
• F35406 Channel 10
• F35407 Channel 11
• F35801 TM DRIVE-CLiQ: Sign-of-life signal missing
• F35804 TM: CRC
• F35805 TM: Incorrect EEPROM checksum
• F35820 TM DRIVE-CLiQ: Telegram error
• F35835 TM DRIVE-CLiQ: Cyclic data transfer error
• F35836 TM DRIVE-CLiQ: DRIVE-CLiQ data transmission error
• F35837 TM DRIVE-CLiQ: Component fault
• F35845 TM DRIVE-CLiQ: Cyclic data transfer fault
• F35850 TM: Internal software error
• F35851 TM DRIVE-CLiQ (CU): Sign-of-life signal missing
• F35860 TM DRIVE-CLiQ (CU): Telegram fault
• F35875 TM DRIVE-CLiQ (CU): Supply voltage fault
• F35885 TM DRIVE-CLiQ (CU): Cyclic data transfer fault
• F35886 TM DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F35887 TM DRIVE-CLiQ (CU): Component fault
• F35895 TM DRIVE-CLiQ(CU): Interactive cyclic data transfer fault
• F35896 TM DRIVE-CLiQ(CU): Component characteristics mismatch
• F35897 DRIVE-CLiQ: No communication to component
• F35899 TM: Unknown fault
• F35950 TM: Internal software error
• F36 Optimization run: Current limit too low
• F36207 Hub: Component overheat fault
• F36214 Hub: 24 V power supply overvoltage fault
• F36216 Hub: 24 V power supply undervoltage fault
• F36804 Hub: checksum error
• F36805 Hub: EEPROM checksum incorrect
• F36820 DRIVE-CLiQ Hub: telegram fault
• F36835 DMC DRIVE-CLiQ: Cyclic data transfer error
• F36836 DRIVE-CLiQ Hub: DRIVE-CLiQ data transmission error
• F36837 DRIVE-CLiQ hub: Component fault
• F36845 DRIVE-CLiQ Hub: cyclic data transfer fault
• F36851 DRIVE-CLiQ hub (CU): Sign-of-life signal missing
• F36860 DRIVE-CLiQ hub (CU): Telegram fault
• F36885 DRIVE-CLiQ hub (CU): Cyclic data transfer fault
• F36886 DRIVE-CLiQ hub (CU): Error sending DRIVE-CLiQ data
• F36887 DRIVE-CLiQ hub (CU): Component fault
• F36895 DRIVE-CLiQ hub(CU): Cyclic data exchange fault
• F36896 DRIVE-CLiQ hub(CU): Component characteristics mismatch
• F36899 Hub: Unknown fault
• F36950 Hub: Internal software error
• F37001 HF Damper: Overcurrent
• F37002 HF Damper: Damping voltage too high
• F37003 HF Damper: Damping voltage not established
• F37004 HF damper: Heatsink overheat
• F37005 HF Damper: Overload I2t
• F37012 HF Damper: Heatsink temperature sensor open
• F37013 HF Damper: Heatsink temperature sensor short circuit
• F37024 HF damper: Thermal model overtemperature
• F37025 HF Damper: Chip overheat
• F37036 HF damper: Internal compartment overtemperature
• F37040 HF Damper: 24 V undervoltage
• F37043 HF damper: 24 V overvoltage
• F37045 HF damper: Power supply undervoltage
• F37050 HF damper: 24 V overvoltage fault
• F37052 HF damper: EEPROM data error
• F37311 HF reactor: Heatsink overtemperature
• F37313 HF Reactor: Overtemperature or fan fault
• F37802 HF damper: Time slice overflow
• F37804 HF damper: CRC
• F37805 HF damper: EPROM checksum incorrect
• F37820 HF damper: Telegram error
• F37835 HF damper: Cyclic data transfer failure
• F37836 HF damper: Failure to send DRIVE-CLiQ data
• F37837 HF damper: Component fault
• F37875 HF damper (CU): Supply voltage fault
• F37885 HF damper (CU): Cyclic data transfer failure
• F37886 HF damper (CU): Failure to send DRIVE-CLiQ data
• F37896 HF damper(CU): Component properties mismatch
• F37899 HF damper: Unknown fault
• F37903 HF damper: I2C bus fault occurred
• F37950 HF damper: Internal software error
• F38013 AIM: Temperature sensor short circuit
• F38018 AIM: Wrong IHD card inserted
• F38040 AIM: 24 V undervoltage
• F38052 AIM: EEPROM data error
• F38058 AIM: Main fan damaged
• F38400 AIM: Component temperature exceeded the fault threshold
• F38403 AIM: Input reactor core temperature exceeded the fault threshold
• F38404 AIM: Input reactor winding temperature exceeded the fault threshold
• F38405 AIM: Input-side ferrite ring temperature T1 fault
• F38803 AIM: Memory test
• F38804 AIM: CRC
• F38805 AIM: EEPROM checksum incorrect
• F38806 AIM: Initialization
• F38810 AIM: Watchdog timer timeout
• F38815 AIM: Processor clock signal error
• F38896 AIM DRIVE-CLiQ (CU): Component characteristics mismatch
• F38899 AIM: Unknown fault
• F38950 AIM: Internal software error
• F39804 IIoT: Checksum error
• F39836 IIoT DRIVE-CLiQ: DRIVE-CLiQ Data send error
• F39837 IIoT DRIVE-CLiQ: Component fault
• F39845 IIoT DRIVE-CLiQ: Cyclic data transmission error
• F39885 IIoT DRIVE-CLiQ (CU): Cyclic data transmission error
• F39886 IIoT DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F39887 IIoT DRIVE-CLiQ (CU): Component fault
• F39896 IIoT DRIVE-CLiQ (CU): Component characteristic mismatch
• F39899 IIoT: Unknown fault
• F39950 IIoT: Internal software error
• F4 Converter overheat
• F40000 DRIVE-CLiQ socket X100 fault
• F40001 DRIVE-CLiQ socket X101 fault
• F40002 DRIVE-CLiQ socket X102 fault
• F40003 DRIVE-CLiQ socket X103 fault
• F40004 DRIVE-CLiQ socket X104 fault
• F40005 DRIVE-CLiQ socket X105 fault
• F40799 CX32: Defined transmission end point exceeded
• F40801 CX32 DRIVE-CLiQ: Sign-of-life signal missing
• F40820 CX32 DRIVE-CLiQ: Telegram fault
• F40825 CX32 DRIVE-CLiQ: Supply voltage fault
• F40835 CX32 DRIVE-CLiQ: Cyclic data transfer fault
• F40836 CX32 DRIVE-CLiQ: DRIVE-CLiQ data send error
• F40837 CX32 DRIVE-CLiQ: Component fault
• F40845 CX32 DRIVE-CLiQ: Cyclic data transfer fault
• F40851 CU DRIVE-CLiQ: Sign-of-life missing
• F40860 CX32 DRIVE-CLiQ (CU): Telegram fault
• F40875 CX32 DRIVE-CLiQ (CU): Supply voltage fault
• F40885 CX32 DRIVE-CLiQ(CU): Cyclic data transfer fault
• F40886 CX32 DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F40887 CX32 DRIVE-CLiQ (CU): Component fault
• F40895 CX32 DRIVE-CLiQ(CU): Cyclic data transfer fault
• F41 Thyristor fault
• F410 Cavitation protection fault
• F42 Thyristor fault
• F43 Thyristor fault
• F44 Thyristor fault
• F45 Thyristor fault
• F452 Load monitoring fault
• F45820 OM-AIO DRIVE-CLiQ: Telegram error
• F45836 OM-AIO DRIVE-CLiQ: DRIVE-CLiQ data send error
• F45837 OM-AIO DRIVE-CLiQ: Component fault
• F45885 OM-AIO DRIVE-CLiQ (CU): Cyclic data transmission error
• F45886 OM-AIO DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F45887 OM-AIO DRIVE-CLiQ (CU): Component fault
• F45896 OM-AIO DRIVE-CLiQ (CU): Component characteristic mismatch
• F45899 OM-AIO: Unknown fault
• F45950 OM-AIO: Internal software error
• F46 Thyristor fault
• F46820 OM-DIO DRIVE-CLiQ: Telegram error
• F46836 OM-DIO DRIVE-CLiQ: DRIVE-CLiQ data send error
• F46837 OM-DIO DRIVE-CLiQ: Component fault
• F46885 OM-DIO DRIVE-CLiQ (CU): Cyclic data transmission error
• F46886 OM-DIO DRIVE-CLiQ (CU): Error sending DRIVE-CLiQ data
• F46887 OM-DIO DRIVE-CLiQ (CU): Component fault
• F46896 OM-DIO DRIVE-CLiQ (CU): Component characteristic mismatch
• F46899 OM-DIO: Unknown fault
• F46950 OM-DIO: Internal software error
• F47 Two or more thyristors cannot be triggered (MI
• F48 Two or more thyristors cannot be triggered (MII
• F48604 SI: safety EEPROM data error
• F48606 SI: Safety hardware version error
• F48899 SI: Unknown fault
• F48999 SI: Unknown alarm
• F49 I=0 signal fault
• F49150 Cooling unit: fault occurred
• F49151 Cooling unit: thermal conductivity exceeded the fault threshold
• F49152 Cooling unit: switch-on command feedback missing
• F49153 Cooling unit: coolant flow too low
• F49154 Cooling unit: leak detected
• F49155 Cooling unit: power stack adapter firmware version too old
• F49156 Cooling unit: coolant temperature exceeded the fault threshold
• F49200 Field general fault signal
• F5 Converter I2t
• F50 External interruption
• F50510 FBLOCKS: Execution cycle group entry rejected
• F50511 FBLOCKS: No storage space available for free function blocks
• F50518 FBLOCKS: Free-running execution cycle group sampling time download deviation
• F51 Thyristor cannot be triggered (gate G11
• F52 Thyristor cannot be triggered (gate G12
• F52903 Mismatch between fault status and faults in the fault buffer
• F52904 Control mode change
• F52911 Forward torque limit error
• F52912 Negative torque limit error
• F52931 Gearbox limitation
• F52933 PTO gearbox limitation
• F52940 FPC: Following error too large
• F52960 Cavitation protection fault
• F52961 Positive hardware limit switch reached
• F52965 MPC No motor available
• F52966 MPC Motor count mismatch
• F52968 Level limit reached
• F52970 OA: Power unit not permitted
• F52972 Level switch status error
• F52973 PUMPFANCTRL parameter error
• F52980 Motor with absolute encoder changed
• F52981 Motor with absolute encoder mismatch
• F52983 No encoder detected
• F52984 Motor with incremental encoder not configured
• F52985 Motor with absolute encoder error
• F52987 Absolute encoder replaced
• F53 Thyristor cannot be triggered (gate G13
• F53430 VIBSUP EPOS not activated
• F53432 VIBSUP frequency fd > Shannon frequency
• F54 Thyristor cannot be triggered (gate G14
• F55 Thyristor cannot be triggered (gate G15
• F56 Thyristor cannot be triggered (gate G16
• F6 Chip temperature exceeds critical value
• F60 Asic timeout
• F60004 "Armature circuit phase failure detected"
• F60005 "Field circuit phase failure detected"
• F60006 "Line monitoring undervoltage"
• F60007 "Line monitoring overvoltage"
• F60008 "Line frequency less than minimum line frequency"
• F60009 "Line frequency greater than maximum line frequenc
• F60010 "Armature circuit uneven
• F60026 Bearing damaged
• F60027 Motor fan damaged
• F60028 Motor overtemperature
• F60029 "Motor temperature fault"
• F60038 Motor overspeed: Speed threshold exceeded
• F60041 Cannot select the ramp-function generator parameter set
• F60045 Static field activated during operation
• F60046 Analog input "Main setting" open
• F60047 Analog input 1 open
• F60050 "Optimization run aborted due to internal cause"
• F60051 "Optimization run limit value violated"
• F60052 "Optimization run aborted due to external cause"
• F60062 "Communication error to the voltage sensing"
• F60063 "Incorrect calibration values for analog inputs/ou
• F60067 "Fault
• F60090 "Fault
• F60092 Reference voltage N10 exceeded tolerance
• F60093 Power supply P5 overload
• F60094 Power supply P15 overload
• F60095 Power supply P24 overload
• F60096 Temperature sensor error
• F60097 Power supply error
• F60099 "System utilization too high"
• F60137 Fault: I2t monitoring detected motor overheat
• F60139 Fault: I2t monitoring detected power unit overheat
• F60167 "Fault fan speed too slow"
• F60203 External fault occurred
• F60204 Fuse monitoring detected an error
• F60267 "CM: Fan not OK"
• F61 Thyristor cannot be triggered (gate G21) (fault message applicable only to four-quadrant rectifiers
• F62 Thyristor cannot be triggered (gate G22) (fault information applicable only to four-quadrant rectifiers
• F63 Thyristor cannot be triggered (gate G23) (fault information applicable only to four-quadrant rectifiers
• F64 Thyristor cannot be triggered (gate G24) (fault information applicable only to four-quadrant rectifiers
• F65 Thyristor cannot be triggered (gate G25) (fault information applicable only to four-quadrant rectifiers
• F66 Thyristor cannot be triggered (gate G26) (fault information applicable only to four-quadrant rectifiers
• F70 I/O expansion module communication fault
• F7011 Motor overheat
• F7085 Open-loop/closed-loop control parameters changed
• F7090 Drive: Torque upper limit is lower than the lower limit
• F7093 Drive: Internal signal error
• F71 Single-quadrant rectifier: Thyristor cannot turn off (gate G11
• F72 Single-quadrant rectifier: Thyristor cannot turn off (gate G12
• F7220 Drive: Missing PLC master control
• F73 Single-quadrant rectifier: Thyristor cannot turn off (gate G13
• F74 Single-quadrant rectifier: Thyristor cannot turn off (gate G14
• F7403 DC bus voltage lower limit reached
• F7404 DC bus voltage upper limit reached
• F7405 Drive: Speed below the minimum for operation in kinetic buffering status. The drive is therefore disabled.
• F7406 Drive: Maximum kinetic buffering duration exceeded). The drive is therefore powered off. In the standard settings, the response to this fault
• F7410 Current controller output limited
• F7412 Commutation angle error (motor model
• F7420 Drive: Current setpoint filter natural frequency > Shannon frequency
• F7430 Cannot switch to open-loop torque operation
• F7431 Cannot switch to operation without an encoder
• F7442 LR: Multi-turn and modulo range mismatch
• F7443 Reference point coordinates outside the permitted range
• F7447 Load gearbox: Position tracking exceeded the maximum actual value
• F7449 Load gearbox: Actual position tracking value exceeded the monitoring window
• F7450 Static monitoring has been triggered
• F7451 Positioning monitoring triggered
• F7452 Following error too large
• F7453 Error processing actual position value
• F7458 EPOS: Reference point cam not found
• F7459 Zero pulse not present
• F7460 EPOS: Reference point cam endpoint not found
• F7464 EPOS: Traversing block mismatch
• F7475 EPOS: Target position < start of travel range
• F7476 EPOS: Target position > end of travel range
• F7481 EPOS: Axis position < negative software limit switch
• F7482 EPOS: Axis position > forward software limit switch
• F7484 EPOS: Fixed stop outside the monitoring window
• F7485 EPOS: Fixed stop not reached
• F7488 EPOS: Cannot perform relative positioning
• F7490 Enable removed during operation
• F7491 Negative limit reached
• F7492 Positive limit reached
• F7493 LR: Actual position value range overflow
• F75 Single-quadrant rectifier: Thyristor cannot turn off (gate G15
• F7575 Drive: Motor encoder not ready
• F7599 Encoder 1: cannot be adjusted
• F76 Single-quadrant rectifier: Thyristor cannot turn off (gate G16
• F7801 Motor overcurrent
• F7802 Infeed or power unit not ready
• F7815 Power unit changed
• F7860 – External fault 1, 698
• F7861 – External fault 2, 698
• F7862 – External fault 3, 699
• F7900 Motor stalled/speed controller at limit
• F7901 Motor overspeed
• F7966 Check the commutation angle
• F7969 Error in magnetic pole position detection
• F7995 Motor identification failure
• F80 Analog input signal loss • Open circuit
• F85 External fault
• F8501 PROFIdrive: setpoint timeout