Siemens F07088 fault code meaning
Siemens / F07088
Series: DCM-6RA80
Unit conversion: Parameter limit exceeded due to unit conversion
DC drive
Meaning: A unit conversion was performed. This may cause parameter limits to be exceeded. Possible causes include: - The static maximum/minimum limit was exceeded when rounding the parameter. - The floating-point data type is imprecise. In this case, the parameter value is rounded up if it is below the minimum limit and rounded down if it exceeds the maximum limit.
Possible causes
Source: SINAMICS DCM, Parameter Manual, firmware version 1.5 SP2 (based on 5.1 SP2) P1007
Series: G110M, G115D, G120-CU240B-E-2, G120-CU250S-2, G120C, G120D, G130-G150, S120-S150
Unit conversion: Parameter limit exceeded due to unit conversion
converter
Meaning: A unit conversion was performed. This may cause parameter limits to be exceeded. Possible causes of parameter limits being exceeded: - Rounding a parameter exceeded its static maximum/minimum limit. - The floating-point data type is imprecise. In this case, parameter values below the minimum limit are rounded up, and parameter values above the maximum limit are rounded down.
Possible causes
Source: SINAMICS G110M P704; SINAMICS G115D P762; SINAMICS G120, Control unit CU240B-2_CU240E-2 P734; SINAMICS G120, Control unit CU250S-2 P1367; SINAMICS G120C P678; SINAMICS G120D Control unit CU240D- 2_CU250D- 2 P868; SINAMICS G130_G150 P1602; SINAMICS S120_S150 P2731
Series: G120-CU230P-2
Unit changeover: Parameter limits exceeded
converter
Meaning:
Possible causes
Source: Converter SINAMICS G120, equipped with control unit CU230P-2 P492
Series: G120P-Cabinet
Unit switching: Parameter limits exceeded
converter
Meaning:
Possible causes
Source: SINAMICS G120P Cabinet P511
Series: G120X, G120XA
Unit conversion: Parameter limit exceeded due to unit conversion
converter
Meaning: A unit conversion was performed. This may cause parameter limits to be exceeded. Possible causes include: - The static maximum/minimum limit was exceeded when rounding the parameter. - The floating-point data type is imprecise. In this case, the parameter value is rounded up if it is below the minimum limit and rounded down if it exceeds the maximum limit.
Possible causes
Source: SINAMICS G120X Converter P1375; SINAMICS G120XA PN Converter P1285
Series: G200, G210, G210X, G220, S220
Unit change: Parameter limits exceeded due to a unit change
converter
Meaning: A unit changeover was performed. This may cause parameter limits to be exceeded. Possible causes of parameter limits being exceeded: - Rounding a parameter exceeded its static maximum/minimum limits. - Inaccuracy of the floating-point data type. In this case, parameter values below the minimum limit are rounded up; parameter values above the maximum limit are rounded down.
Possible causes
Source: SINAMICS G200 converter P704; SINAMICS G210 converter P1100; SINAMICS G210X converter P962; SINAMICS G220 converter P1317; SINAMICS S220 converter P2263
Series: S110
Unit conversion: Parameter limit exceeded due to unit conversion
servo drive
Meaning: A unit conversion has been performed. Possible causes of parameter limits being exceeded: - Rounding a parameter exceeded its static maximum/minimum limits. - Inaccuracy of the floating-point data type. In this case, parameter values below the minimum limit are rounded up, and values above the maximum limit are rounded down.
Possible causes
Source: SINAMICS S110 P1008
Series: S200
Unit change: Parameter limits exceeded due to a unit change
servo drive
Meaning: A unit changeover was performed. This may cause parameter limits to be exceeded. Possible causes of parameter limits being exceeded: - Rounding a parameter exceeded its static maximum/minimum limits. - Inaccuracy of the floating-point data type. In this case, parameter values below the minimum limit are rounded up; parameter values above the maximum limit are rounded down.
Possible causes
Source: SINAMICS S200 PROFINET_SIMOTICS S-1FL2 P513