Siemens A07089 fault code meaning
Siemens / A07089
Series: DCM-6RA80
Unit conversion: Function block cannot be activated after unit conversion
DC drive
Meaning: An attempt was made to activate a function block. This operation is not permitted after changing units.
Possible causes
Source: SINAMICS DCM, Parameter Manual, firmware version 1.5 SP2 (based on 5.1 SP2) P1007
Series: G110M
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after converting units. See: p0100 (Standard IEC/NEMA), p0505 (Unit system selection)
Possible causes
Source: SINAMICS G110M P704
Series: G115D, G120C, G120D
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after changing units. See also: p0100 (Standard IEC/NEMA), p0505 (Unit system selection).
Possible causes
Source: SINAMICS G115D P762;SINAMICS G120C P678;SINAMICS G120D Control Unit CU240D- 2_CU250D- 2 P868
Series: G120-CU240B-E-2
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after unit conversion. See: p0100 (Motor standard IEC/NEMA), p0505 (Unit system selection)
Possible causes
Source: SINAMICS G120, Control Unit CU240B-2_CU240E-2 P734
Series: G120-CU250S-2
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after unit conversion. See: p0100 (Motor standard IEC/NEMA), p0349 (Motor equivalent circuit data unit system), p0505 (Unit system selection)
Possible causes
Source: SINAMICS G120, Control Unit CU250S-2 P1367
Series: G120X, G120XA
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after changing units. See also: p0100, p0505
Possible causes
Source: SINAMICS G120X Converter P1375; SINAMICS G120XA PN Converter P1285
Series: G130-G150, S120-S150
Unit conversion: Function block cannot be activated after unit conversion
converter
Meaning: An attempt was made to activate a function block. This operation is not permitted after changing the system of units. See also: p0100 (Standard IEC/NEMA), p0349 (System of units for motor equivalent circuit data), p0505 (System of units selection)
Possible causes
Source: SINAMICS G130_G150 P1602;SINAMICS S120_S150 P2731
Series: G200
Unit switching: Function cannot be activated after changing units
converter
Meaning: An attempt was made to activate a function. This operation is not permitted after changing units. See also: p0100 (standard IEC/NEMA), p0505 (unit system selection). System message 14.3 Faults and alarms SINAMICS G200 Converter 702 Operating Instructions, 06/2026, FW V6.7, A5E54053464B AA
Possible causes
Source: SINAMICS G200 Converter P704
Series: G210, G210X
Unit switching: Function cannot be activated after changing units
converter
Meaning: An attempt was made to activate a function. This operation is not permitted after converting units. See also: p0100 (Standard IEC/NEMA), p0349 (Motor equivalent circuit data unit system), p0505 (Unit system selection)
Possible causes
Source: SINAMICS G210 converter P1100; SINAMICS G210X converter P962
Series: G220, S220
Unit switching: Function cannot be activated after changing units
converter
Meaning:
Possible causes
Source: SINAMICS G220 Converter P1317; SINAMICS S220 Converter P2263
Series: S110
Unit conversion: Function block cannot be activated after unit conversion
servo drive
Meaning: An attempt was made to activate a function block. This operation is not permitted after unit conversion. See: p0100 (Motor standard IEC/NEMA), p0349 (Motor equivalent circuit data unit system), p0505 (Unit system selection).
Possible causes
Source: SINAMICS S110 P1008
Series: S200
Unit switching: Function cannot be activated after changing units
servo drive
Meaning: An attempt was made to activate a function. This operation is not permitted after unit conversion. System messages 12.3 Faults and alarms SINAMICS S200 PROFINET servo drive system with SIMOTICS S-1FL2 Operating Instructions, 06/2026, FW V6.7, A5E51646752F AG 511
Possible causes
Source: SINAMICS S200 PROFINET_SIMOTICS S-1FL2 P513