BALDOR fault codes

Fault codes

• --- Parameter initialization (status display)
• -| Limit switch (clock wise) active
• . Amplifier enabled
• 1 Non-resettable hardware fault
• 15V Control power supply fault
• 2 Overload
• 2 SEC Overload * Output current exceeded 3 second rating.
• 24V FAILURE 24V FAILURE 24V output overload (warning only)
• 3 DC bus error
• 3 SEC Overload 3-second overload
• 4 Dynamic braking or overheat
• 5 Microprocessor fault
• 6 Monitor 6
• 7 Monitor 7
• AC Input High AC input too high (alarm)
• ADC Calib Fault Internal ADC calibration voltages out of range.
• AMBIENT TEMP Ambient temperature fault
• Aux Filter Setup Auxiliary filter setting (alarm)
• BRAKE RESISTOR Braking resistor overload
• BRAKE SHORT CCT Braking circuit short circuit
• BUS Overvoltage High DC Bus voltage.
• Brake Desat Brake desaturation
• Bus Current SENS Failure to sense bus current.
• Bus Undervoltage DC bus undervoltage
• CAU CHANGE OF MAX FREQ. OR MODE
• CONTACTOR FBK Contactor feedback fault
• CUR LIM Timeout Current limit timeout
• Comm Watchdog Indicates a problem with the serial communications.
• Commun Timeout Communication timeout
• Configuration Configuration error
• Co–Processor Fault Co-Processor hardware fault occurred. Contact Baldor.
• Current SENS FLT Phase current detection fault
• Current Sense Current detection fault
• Current reference Current reference
• DC Bus High Bus over voltage condition occurred.
• DC Bus Low Bus under voltage condition occurred.
• DC Bus Short DC bus short circuit
• DC PK Overvolt DC peak overvoltage
• DESAT (OVER I) DESATURATION (Over I)
• Desaturation Desaturation
• Download Download
• Drive Disabled Inverter not enabled (alarm)
• Drive Enabled Inverter enabled (alarm)
• Drive Low TEMP Inverter temperature too low
• Drive Over TEMP Inverter overheat
• Dyn Brake Desat Dynamic braking desaturation
• EEPROM fault EEPROM fault (power board EE, control EE, fault log, NVM)
• ENCODER 1 FAULT Encoder 1 fault
• ERR MALFUNCTION OF MICROCOMPUTER
• EXB Selection Expansion board selection fault
• EXTERNAL TRIP External trip
• Encoder Loss Encoder loss
• Excess Faults/Hr Too many faults per hour (alarm)
• External Trip External trip
• External trip External trip
• F01 Computer Malfunction
• F02 Parameter Block Fault
• F03 Bus Current Measurement Fault
• F04 Power Supply Overload
• F05 No DC Bus Voltage
• F06 Output Short Circuit
• F07 External Trip Fault
• F10 Auto Restart Fault
• F11 Ground Fault
• F13 DC Bus Overvoltage
• F16 Overcurrent During Acceleration
• F17 Overcurrent During Deceleration
• F18 Overcurrent While Running
• F19 Heatsink Overtemperature
• F20 Timed Overload
• FE EEPROM Error Feedback module EEPROM error
• FLT Log MEM Fail Fault log memory error
• Fan Loss Fan loss (alarm)
• Feedback Module Indicates a problem with the feedback device.
• Following ERR Following fault
• Following Error Following fault
• GND FLT Ground fault
• Ground fault Ground fault
• H Hold - Position Mode
• HEATSINK Heatsink overheat
• HW Desaturation Hardware desaturation (high output current)
• HW Ground Fault Hardware ground fault
• HW Power Supply Control board power supply fault
• HW Surge Current Hardware surge current
• Hardware Protect Hardware
• Heat Sink Temp Heatsink overtemperature
• High INIT CUR Initial current too high
• ID:No Feedback No encoder feedback in auto-tuning
• INPUT 1 BREAK Input 1 disconnected
• INPUT 2 BREAK Input 2 disconnected
• INT Over-Temp Temperature of control heatsink exceeded safe level.
• Initial Pos Initial position (alarm)
• Internal Config Internal configuration error
• Invalid Base ID Control does not recognize power base ID.
• Invalid FB Sel Feedback selection invalid (alarm)
• Invalid Res Sel Resolver selection invalid (alarm)
• Inverter Base ID Inverter board ID
• J JOG - Mode
• L Both limit switches active
• LOST COMMS Communication loss
• Line Loss Mains loss (alarm)
• Line Sag Mains voltage dip (alarm)
• Logic Supply FLT Logic power supply not working properly.
• Logic supply Logic power supply
• Lost AB Phase AB phase loss
• Lost BC Phase BC phase loss
• Lost User Data User data loss
• Low INIT Bus V Insufficient bus voltage on startup.
• Low Initial BUS DC bus voltage low at power-on
• MAG CURRENT FAIL Field current failure (auto-tuning)
• MAX RPM DATA ERR Maximum speed data error
• MAX SPEED LOW Maximum speed too low (auto-tuning)
• MOTOR OVERTEMP Motor overheat
• MOTOR STALLED MN737 Table D-1 Trip Name (MMI)
• Memory Memory fault
• Memory Error EEPROM error occurred. Contact Baldor.
• Motor Overload Motor overload
• Motor Overtemp Motor overheat (alarm)
• NV Memory Fail Non-volatile memory error
• Network Timeout Forced network fault. Possible reason
• New Base ID Power board ID changed
• New base ID New power baseboard ID
• OFF Amplifier disabled
• OL Overload
• OP STATION OP Station (KEYPAD)
• OT Overtemperature
• OV DC bus overvoltage
• OVERCURRENT Overcurrent
• OVERSPEED Overspeed
• OVERVOLTAGE Overvoltage
• Opt1 Protocol or Opt2 Protocol Opt1/Opt2 protocol (alarm)
• Option Not Found Option not found (alarm)
• Over Current FLT Overcurrent
• Over Speed Rotor speed over 110% maximum speed limit.
• Over current Overcurrent
• Over speed Overspeed
• Overcurrent Continuous current limit exceeded.
• Overcurrent FLT Overcurrent
• Overload Overload
• Overload - 1 min Output current exceeded 1 minute rating.
• Overload - 1 minute Overload – 1 minute
• Overload - 1.5 sec Output current exceeded 1.5 second rating.
• Overload - 3 sec Output current exceeded 3 second rating.
• Overload - 3 seconds Overload – 3 seconds
• Overload - 7 sec Output current exceeded 7 second rating.
• PB Power Supply Power baseboard power supply (alarm)
• PF Setup Pulse following setting (alarm)
• PLC Mode Trip PLC mode trip
• PWR Base FLT Power board fault
• Param Checksum Parameter checksum and error
• Parameter Parameter
• Ph1 pulse Ph1 cycle-by-cycle current limit
• Ph2 pulse Ph2 cycle-by-cycle current limit
• Ph3 pulse Ph3 cycle-by-cycle current limit
• Phase Loss Phase loss (alarm)
• Pos Cnt Overflow Position count overflow
• Power Base FPGA Power baseboard FPGA
• Power Base Fault Power baseboard fault
• Power Module Power module fault
• Pre-charge Fault Pre-charge fault
• Precharge FLT Pre-charge fault
• REGEN RES Power Braking resistor power too large
• Regen R PWR FLT Regen power exceeded DB resistor rating.
• Regen R or PWR Regeneration resistor or power
• Resolver Loss Resolver loss
• SPEED FEEDBACK Speed feedback fault
• SPI timeout SPI timeout
• ST LED red steady on Overload (120% – 160% Full Load)
• ST LED red fast blinking I2t (Drive Timed Out)
• ST LED red slow blinking Short Circuit
• ST LED red/yellow fast blinking Undervoltage
• ST LED red/yellow slow blinking Overvoltage
• Sel FB Source Feedback source selection (alarm)
• Software VER FLT Software version error
• Sync To Line Mains synchronization fault
• Torque Prove FLT Unbalanced current between all 3 motor phases.
• Torque Proving Torque verification (three-phase current imbalance)
• U Version fault
• U Lower Fault Power transistor gate fault on T1.
• U Upper Fault Power transistor gate fault on T1.
• UNDERVOLTAGE Undervoltage
• UV DC bus undervoltage
• Unknown FLT Code Unknown fault code
• Unknown system fault Unknown system fault
• User 24 V User 24V
• User Fault Text Custom software operating fault occurred.
• User ref Internal reference power supply out of tolerance.
• V Lower Fault Power transistor gate fault on T2.
• V Upper Fault Power transistor gate fault on T2.
• VDC RIPPLE DC bus ripple too high
• W lower fault Power transistor gate fault on T3.
• W upper fault Power transistor gate fault on T3.
• _L Input voltage insufficient
• _OC Overcurrent trip
• _OL External thermal protection trip
• _OU Overvoltage trip
• _RP Manual restart (status display)
• d Amplifier disabled
• mP Reset Microprocessor reset
• |- Limit switch (counter clock wise) active
• µP RESET Microprocessor reset
• Ø1 Phase fault T1
• Ø2 Phase fault T2
• Ø3 Phase fault T3