Xinje fault codes

Fault codes

A32 Synchronous motor tuning failed; stop
A33 Power-loss ride-through hysteresis timeout
A34 Power-loss ride-through hysteresis
A37 Encoder battery undervoltage warning
A70 PID open warning
E-001 Program damaged
E-002 Parameter damaged
E-003 DC bus overvoltage
E-004 DC bus undervoltage
E-005 Regenerative resistor fault
E-006 Module overtemperature
E-007 Overcurrent
E-008 Overspeed
E-009 Analog input fault
E-01 Inverter overcurrent during acceleration
E-010 Firmware version mismatch
E-011 Motor UVW short circuit
E-012 System firmware incomplete
E-013 FPGA load fault
E-014 FPGA access fault
E-015 Program run error
E-016 Hard fault
E-017 Processor run timeout
E-018 Erase parameter error
E-019 System password error
E-02 Inverter overcurrent during deceleration
E-020 Parameter load error
E-021 Parameter out of range
E-022 Parameter conflict
E-023 Sampling channel setting error
E-024 Parameter loss
E-025 Erase FLASH fault
E-026 Initialization FLASH fault
E-028 EEPROM write error
E-029 EEPROM write frequent alarm
E-03 Inverter constant speed run overcurrent
E-030 DC bus voltage overvoltage
E-031 Motor code error
E-032 System initialization failure
E-04 Inverter overvoltage during acceleration
E-040 DC bus voltage undervoltage
E-041 Drive power loss
E-043 DC bus voltage charging failure
E-044 Three-phase input phase loss
E-045 Frequent parameter save alarm
E-05 Inverter overvoltage during deceleration
E-06 Inverter constant speed run overvoltage
E-060 Module overtemperature
E-061 Motor overheat alarm
E-062 Drive overcooling
E-063 Thermistor open alarm
E-07 Inverter control
E-070 Current too large
E-08 Inverter overheat
E-080 Overspeed alarm
E-082 Encoder zero position deviation 1
E-083 Speed command out of range
E-09 Inverter overload
E-092 Analog Tref zero calibration out of range
E-093 Analog Vref zero calibration out of limit
E-10 Motor overload
E-100 Excessive position deviation
E-101 Sudden position command deviation
E-102 Software overvoltage
E-103 Overtemperature
E-104 Discharge tube shorted; discharge tube damaged
E-105 Discharge tube disconnected
E-106 Continuous braking timeout
E-109 External alarm input
E-110 External UVW short circuit found during self-test
E-111 P+ current overcurrent
E-112 U phase current overcurrent
E-113 V phase current overcurrent
E-114 U/V/W phase current
E-115 Phase U short circuit (22–32 kW only)
E-116 Phase V short circuit (22–32 kW only)
E-117 U/V/W phase short circuit
E-12 Inverter module fault
E-120 Current sensor fault
E-122 Phase V current sampling zero calibration
E-13 External device fault
E-130 Motor quadrature encoder fault
E-14 Current detection fault
E-142 Motor quadrature encoder Z
E-15 RS485 communication error
E-150 Motor power cable open
E-16 System interference
E-160 Motor output power overload
E-161 Drive thermal power overload
E-164 DC bus capacitor overload
E-165 Anti-stall alarm
E-166 Motor holding brake error closed
E-167 Motor holding brake error disconnected
E-17 E2PROM
E-170 Motor during operation undervoltage
E-200 Braking resistor overload
E-201 Regeneration resistor continuous discharge
E-220 Absolute servo encoder communication error
E-221 Too many encoder communication CRC errors
E-222 Absolute servo encoder battery low voltage alarm
E-223 Absolute servo encoder data access alarm
E-224 Absolute servo encoder fault
E-226 TAMA optical encoder overtemperature alarm
E-227 Power-on encoder multi-turn signal data error
E-228 Absolute servo encoder value overflow
E-229 Encoder electrical angle deviation
E-236 Motor encoder feedback and displacement sensor feedback deviation
E-237 Full closed-loop motor encoder and external scale count fault
E-238 Full closed-loop external scale overspeed
E-240 Encoder position data read timing error
E-241 Garbled encoder response data
E-242 Phase finding failed
E-243 HALL status fault
E-244 BISS-C encoder fault
E-250 Homing error alarm
E-260 Overtravel alarm
E-261 Overtravel signal connection fault
E-262 Controlled stop timeout
E-264 Excessive vibration
E-265 Motor vibration too large
E-280 Access motor parameters failed
E-281 Error while writing data to encoder EEPROM
E-282 Station number assignment detection timeout
E-283 Rectifier module temperature over
E-285 Rectifier module P-overcurrent; P-side discharge tube
E-300 Lost sync with motion bus
E-310 Motor power mismatch
E-311 Motor code lost
E-312 Motor parameters corrupted on read
E-313 Encoder software version mismatch
E-314 Encoder software version not supported
E-315 Cannot read valid motor parameters
E-316 Motor code read does not match set code
E-320 External terminal emergency alarm
E-330 Gantry sync deviation alarm
E-331 Gantry communication alarm
E-332 Gantry communication CRC error
E-333 Gantry single-axis alarm
E-334 Gantry mode configuration alarm
E-335 Gantry mode parameter sync failed
E-336 Gantry homing alarm
E-337 Gantry signal mismatch
E-338 Torque deviation alarm
E-339 Not aligned when starting synchronous motion alarm
E-340 STO status not synchronized
E-341 FPGA and CPU init
E-342 STO soft-charge circuit error alarm
E-343 EDM circuit fault
E-344 Main slave axis STO status mismatch
E-400 Slave open connection
E-401 Rectifier unit did not detect inverter module
E-800 Incorrect value
E-801 Undefined ESM request fault
E-802 Boot state request fault
E-803 PLL incomplete fault
E-804 PDO watchdog
E-806 PLL fault
E-807 Sync signal fault
E-810 Sync cycle setting error
E-811 Mailbox setting error
E-814 PDO watchdog setting error
E-815 DC setting error
E-816 SM event mode setting error
E-850 TxPDO assignment
E-851 RxPDO assignment
E-852 And CANopen master
E-881 Control mode setting error
E-882 ESM request error during operation
E-883 Abnormal operation error
E-899 Program cannot access bus correctly
EEEE1 Panel and CPU communication error
Err01 Acceleration overcurrent
Err02 Deceleration overcurrent
Err03 Constant speed overcurrent
Err04 Acceleration overvoltage
Err05 Deceleration overvoltage
Err06 Constant speed overvoltage
Err07 Snubber resistor overload fault: supply voltage unstable
Err08 Undervoltage
Err09 Inverter overload
Err10 Motor overload
Err11 Input phase loss
Err12 Output phase loss
Err13 Heatsink overheat/module overheat
Err14 Contactor fault
Err15 External fault
Err16 Motor tuning fault
Err17 User-defined fault 2
Err18 Motor ground fault motor ground fault
Err19 Load loss
Err20 Cycle-by-cycle current limit fault
Err21 Magnetic pole position detection failed: motor parameters deviate too much from actual
Err22 Communication (timeout) error
Err23 Braking resistor short circuit
Err24 Load loss
Err25 Run time reached
Err26 SVC stall fault
Err27 Power-on time reached
Err28 PID feedback loss during operation
Err35 Synchronous motor running untuned
Err37 Encoder battery low
Err43 External fault
Err44 Communication (timeout) error
Err45 EEPROM read/write error
Err46 Run time reached
Err47 Power-on time reached
Err48 User-defined fault 1
Err49 User-defined fault 2
Err50 PID feedback loss during operation
Err51 Motor switchover during operation
Err52 Excessive speed deviation
Err53 Motor overspeed
Err54 Motor overtemperature
Err56 Power-on locked time
Err57 Constant-pressure water supply water shortage fault; water pressure too low
Err58 Power-on locked time
Err63 Multi-step lockout time reached
Err70 PID disconnected
Err71 STO not synchronized