SINEE fault codes

Fault codes

• 0001H Forward run
• 0002H Reverse run
• 0003H JOG forward
• 0004H JOG reverse
• 0005H Slave stop
• 01H Illegal command code
• 02H Invalid data address
• 03H Invalid data
• 04H Slave operation failed
• 05H Command valid, processing
• 121 Encoder A disconnected
• 122 Encoder B disconnected
• 126 Channel check fault: wireless config failed/wireless communication timeout
• A3 CRC checksum Hi
• AL.001 Short circuit fault
• AL.002 Hardware overcurrent
• AL.003 AD initialization fault
• AL.004 Memory error
• AL.005 System parameter error
• AL.006 AD sampling fault
• AL.007 Encoder fault 1
• AL.008 Encoder fault 2
• AL.009 Encoder fault 3
• AL.00A Undervoltage
• AL.00B Overvoltage
• AL.00C Software overcurrent
• AL.010 Drive overheat
• AL.012 Overspeed
• AL.013 Excessive position deviation
• AL.014 Input phase loss
• AL.015 Motor phase sequence error
• AL.016 Drive parameter error
• AL.017 Braking resistor overload
• AL.018 Encoder overheat
• AL.019 Absolute encoder battery voltage low
• AL.01A Absolute encoder battery voltage too low
• AL.01C Homing failed
• AL.01D Power supply power loss
• AL.01F Power loss restart
• AL.01d Main power supply power loss
• AL.021 CANopen network communication error
• AL.027 UVW ground fault alarm
• AL.02c Servo drive temperature sensor fault
• AL.033 Input pulse frequency too high
• AL.036 PID feedback open
• AL.045 Full closed-loop position deviation too large
• AL.048 Servo motor locked rotor
• AL.E02 Drive overheat warning
• AL.E03 Motor overload warning
• AL.E04 Drive overload warning
• AL.E05 Excessive position deviation warning
• AL.E06 Braking overload warning
• AL001 Short circuit fault
• AL002 Hardware overcurrent
• AL003 AD initialization fault
• AL004 Memory error
• AL005 System parameter error
• AL006 AD sampling fault
• AL007 Encoder fault 1
• AL008 Encoder fault 2
• AL009 Encoder fault 3
• AL00A Undervoltage
• AL00B Overvoltage
• AL00C Software overcurrent
• AL010 Drive overheat
• AL012 Overspeed
• AL013 Excessive position deviation
• AL014 Input phase loss
• AL015 Motor phase sequence error
• AL016 Drive parameter error
• AL017 Braking resistor overload
• AL018 Encoder overheat
• AL019 Absolute encoder battery voltage low
• AL01A Absolute encoder battery voltage too low
• AL01C Homing failed
• AL01F System restart
• AL01d Power supply power loss
• AL022 EtherCAT communication disconnected
• Al001 Short circuit fault
• Al003 AD initialization alarm
• Al004 Memory error alarm
• Al006 AD sampling alarm
• Al00D Motor overload
• Al00E Drive overload
• Al00F Motor runaway
• Al016 Parameter setting error
• Al019 Absolute encoder battery voltage low warning
• Al01d Main power supply power loss
• Al021 CAN network communication error
• Al027 UVW ground fault alarm
• Al028 Inertia identification failed
• Al029 Read/write encoder EEPROM error
• Al02B Motor overheat
• Al02C Servo drive temperature sensor fault
• Al02b Motor overheat
• Al033 Input pulse frequency too high
• Al036 PID feedback open
• Al045 Full closed-loop position deviation too large
• Al048 Servo motor locked rotor
• Al04B STO status mismatch
• Al050 DC bus voltage over undervoltage
• Al051 Motor motor power cable disconnected
• C002 Pump feedback disconnected
• C003 Pipe network overpressure
• C004 Supply tank water shortage
• C005 Motor overload during rotation switching
• C006 Output phase loss during rotation switching
• C17 Upper limit warning
• C18 Lower limit warning
• C19 Door limit warning
• C20 Overall limit warning
• C21 Pulse loss
• C22 Encoder open
• C23 Encoder opposite to run direction
• C27 Hoist zero-servo action warning
• C28 Brake power-up check failed (warning)
• C30 PG card not detected in closed-loop control
• C33 Undervoltage warning
• COE Communication timeout error
• E01 Short circuit fault
• E02 Instantaneous overcurrent
• E03 Instantaneous overvoltage
• E04 Steady-state overcurrent
• E05 Overvoltage
• E06 Undervoltage
• E07 Input phase loss
• E08 Output phase loss
• E09 Inverter overload
• E10 Inverter overheat
• E100 Winder output phase loss
• E101 Winder auto-tuning fault
• E102 Encoder reverse fault
• E103 Winder stall fault
• E105 Winder controller overload
• E106 Winder motor overload
• E107 Phase sequence error
• E108 Phase sequence imbalance error
• E109 Input overvoltage
• E11 Parameter setting conflict
• E110 Input undervoltage
• E111 KM2 stuck fault
• E112 Holding brake short circuit
• E113 Traverse steady-state overvoltage
• E114 Holding brake disconnected
• E115 Occupancy detection communication error
• E116 Traverse output phase loss
• E117 DTU module initialization failure
• E118 Traverse current detection circuit fault
• E119 Traverse stall fault
• E12 Motor overload
• E120 Encoder AB disconnected
• E121 Encoder A disconnected
• E122 Encoder B disconnected
• E124 Traverse controller overheat
• E125 Landing-door limit fault
• E13 Motor overload
• E14 External
• E15 Inverter memory fault
• E16 Communication error
• E17 Inverter temperature sensor fault
• E18 Soft-start relay not closed
• E19 Current detection circuit fault
• E20 Stall
• E21 PID feedback open
• E22 Encoder fault
• E23 Keypad memory error
• E24 Auto-tuning fault
• E25 Motor overspeed
• E26 Load loss
• E27 Accumulated power-on time reached
• E28 Cumulative run time reached
• E29 Internal communication error
• E30 Brake sensor fault
• E31 Joystick not at zero
• E32 Start check fault
• E33 Position following fault
• E34 Full closed-loop position following fault
• E35 Motor locked rotor
• E36 Absolute encoder open
• E37 Encoder type setting incorrect
• E38 Encoder battery voltage low warning
• E39 PROFIBUS-DP parameterization data error
• E40 Profibus-DP configuration data error
• E41 Profibus-DPIO connection disconnected
• E42 Encoder battery voltage low fault
• E43 Encoder multiturn data error
• E44 PID feedback open
• E45 Encoder overheat
• E46 Encoder count overflow
• E47 Oil temperature overlimit fault
• E48 CANopen timeout
• E49 Motor temperature out of range
• E50 Motor PTC disconnected
• E51 Encoder line count fault
• E52 External air filter fault
• E53 External oil filter fault
• E54 External oil separator fault
• E55 Fan overload
• E56 Pump fault
• E57 Pipe network overpressure
• E58 Pipe network undervoltage
• E59 Supply tank water shortage fault
• E6 CRC checksum Lo
• E60 Fan overcurrent
• E61 CANSinee communication timeout
• E64 Fan input phase loss
• E65 Air compressor time limit reached
• E66 Fan output phase loss
• E67 Fan output fault
• E72 Encoder opposite to run direction
• E75 Locked rotor fault
• E76 Ground fault
• E77 Swing-arm feedback fault
• E78 Left/right reversing switch fault
• E79 Left limit
• E80 Right limit
• E81 Encoder pulse count fault
• E82 Drum reducer fault
• E86 Brake power-up check failed (fault)
• E87 Tower crane hoist start inhibited fault
• E88 Safety gear fault
• E89 Anti-overshoot fault
• E90 Feed door fault
• E91 Discharge door fault
• E92 Skylight fault
• E93 Emergency stop fault
• E94 KM2 feedback fault
• E95 KM41 pull-in fault
• E96 KM41 feedback fault
• E97 Face recognition fault
• E98 Take-up steady-state overcurrent
• E99 KM42 feedback fault
• EED Inverter memory error
• EEU Keypad memory error
• EHT External fault
• EPC Mechanical service time reached
• EST PID open /SPI fault /SCI fault
• EXT External fault
• Err02 Acceleration overcurrent
• Err03 Deceleration overcurrent
• Err04 Constant speed overcurrent
• Err05 Acceleration overvoltage
• Err06 Deceleration overvoltage
• Err07 Constant speed overvoltage
• Err08 Power-on buffer relay not engaged
• Err09 Undervoltage
• Err10 Drive overload
• Err11 Motor overload
• Err12 Input phase loss
• Err13 Output phase loss
• Err14 Module overheat
• Err15 Output-side fault
• Err16 Current control fault
• Err17 Encoder reference signal error
• Err18 Current detection fault
• Err19 Motor tuning fault
• Err20 Speed feedback fault
• Err22 Leveling signal fault
• Err24 RTC clock fault
• Err25 Storage data error
• Err26 Earthquake signal
• Err29 Star-short contactor feedback fault
• Err30 Elevator position fault
• Err33 Elevator speed fault
• Err34 Logic fault
• Err35 Shaft auto-tuning data error
• Err36 Run contactor feedback fault
• Err37 Holding brake contactor feedback fault
• Err38 Rotary encoder signal fault
• Err39 Motor overheat
• Err40 Elevator run timeout
• Err41 Safety circuit open
• Err42 Door lock opened during operation
• Err43 Upper limit signal fault
• Err44 Lower limit signal fault
• Err45 Forced deceleration switch fault
• Err46 Re-leveling fault
• Err47 Door-shorting contactor fault
• Err48 Door opening fault
• Err49 Door closing fault
• Err50 Leveling signal lost consecutively
• Err51 CAN communication error
• Err52 Hall call communication error
• Err53 Door lock fault
• Err54 Inspection start overcurrent
• Err55 Floor change stop fault
• Err57 SPI communication error
• Err58 Position protection switch fault
• Err62 Analog disconnected
• HOC Instantaneous overcurrent
• HOU Instantaneous overvoltage
• ILP Input phase loss
• INP Internal fault
• IlP Input phase loss overload
• MOH Module overheat
• MS Lamp off/green flash/green on/red flash/red on
• OH Heatsink overheat
• OL Inverter overload
• OLI Motor overload
• OLP Output phase loss
• Ol Overload
• Ol1 Motor overload
• OlP Output phase loss
• PDN PID lower limit
• PG Feedback frequency
• PIDE PID feedback open
• PUP PID upper limit
• SC Short circuit fault
• SCE No-load current fault
• SFE Self-test coast to stop
• SIE No-load current fault
• SLU Steady-state undervoltage
• SOC Steady-state overcurrent
• SOFT Inverter soft-start relay disconnected
• SOH Heatsink overheat
• SOU Steady-state overvoltage
• SPI Communication error
• SRE Stator resistor fault
• STP Auto-tuning cancelled
• SlU Steady-state undervoltage
• SrE Stator resistor fault
• TBR Temperature sensor open
• US Lamp off/green flash/green on/red flash/red on
• ZOH Rectifier bridge overheat
• pUP Pressure too high