SEW fault codes
Fault codes
- 01 Over-current
- 03 Motor power cable ground fault
- 04 Brake chopper
- 06 Power supply phase fault
- 07 UZ overvoltage
- 08 Speed monitoring
- 1 Overcurrent
- 10 Emergency stop
- 11 Overtemperature
- 12 Mot. overload
- 13 Starting conditions
- 14 Output open
- 17 Stack overflow Imm
- 17-24 System fault
- 18 Stack underflow
- 19 NMI trap
- 2 DC link voltage
- 20 Undefined opcode
- 21 Protected instr.
- 22 Word op. access
- 23 Instruct. access
- 24 Ext. bus access
- 25 Rapid stop with inhibit
- 26 External terminal
- 27 Ext. terminal
- 28 Fault INTERBUS
- 3 Brake chopper
- 31 TF sensor
- 32 Index overrun
- 33 Master-slave
- 34 Ramp timeout
- 35 Connection Encoder-FRS
- 36 Connection Master-slave
- 37 Watchdog timer Imm swi
- 38 System software
- 39 FRS parameter Rapi data fault
- 4 Cont. overload
- 41 FRS lag fault ®
- 42 Deviation
- 43 RS485 overflow
- 44 Device overload
- 45 Initialization
- 46 System bus 2 overflow
- 47 System bus 1 overflow
- 48 Hardware DRS
- 5 Regenerative overload
- 50 Limit switch missing
- 51 Zero pulse missing
- 52 Limit switches reversed
- 53 Reference cam Imm
- 54 Motor overload Ra
- 55 Invalid IPOS command
- 56 User watchdog Rap (in positioning program)
- 57 Teach error
- 58 Invalid control word
- 59 Software limit switches
- 6 Overtemperature
- 60 Lag error
- 61 Fault during reference travel
- 62 Index overflow Im
- 63 Jump command error
- 64 Limit switch CW
- 65 Limit switch CCW
- 66 Hardware configuration
- 67 HW watchdog timer
- 7 Phase failure
- 77 IPOSplus control word
- 78 IPOSplus software limit switch
- 79 HW configuration (hardware configuration)
- 80 N registration
- 81 Start condition
- 82 Output disconnected
- 84 Motor protection switch
- 86 Memory module fault
- 87 Technology function
- 88 Start
- 93 DIP encoder fault
- 94 EEPROM checksum
- 97 97 1 No 6.3 No.
- AKO LED Armature circuit open circuit
- BSP○ ESB○ POM○ NEM○ ISP○ AKO○ Motor does not start
- BSP○ ESB● POM● or NEM● ISP● AKO○ Motor does not start
- BSP● ESB○ POM● or NEM● ISP○ AKO○ Motor does not start
- BSP● ESB● POM○ NEM● ISP○ AKO○ Motor can run in one direction only (single torque direction)
- BSP● ESB● POM● NEM○ ISP○ AKO○ Motor can run in one direction only (single torque direction)
- BSP● ESB● POM●⇄NEM○ ISP◐ AKO○ Speed oscillation
- BSP● ESB● POM● or NEM● ISP○ AKO○ Motor does not start
- BSP● ESB● POM● or NEM● ISP● AKO○ Motor does not start
- BSP● ESB● POM● or NEM● ISP● AKO● Motor does not start
- BSP LED Operating voltage o.k.
- ESB LED Current limit raised (status display)
- F01 MAS... / MKS... overcurrent
- F03 MPx… overtemperature
- F05 Message bus connection
- F06 Earth fault
- F07 DC link
- F08 Speed monitoring
- F09 S1 AI011 current
- F11 MAS... / MKS... overtemperature
- F14 Resolver fault
- F15 Internal 24V
- F17-F24 F17...24 Displays detailed fault indicators
- F25 Error while accessing EEPROM
- F26 External terminal
- F27 ES cable missing
- F28 Fieldbus timeout
- F29 Limit switch reversed
- F31 Short circuit output
- F32 Setpoint source n.a.
- F34 Fieldbus timeout
- F36 Required hardware missing
- F43 PC control time
- F87 Fieldbus timeout Displays undefined messages
- ISP LED Pulse inhibit inactive (pulse enable)
- NEM LED Negative torque (braking)
- POM LED Positive torque (driving)
- TMP LED Applicable only to MOVIRET® 3150