Sunye fault codes
Fault codes
- A001 Communication command error
- A002 Communication address error
- A003 Communication data error
- A005 Communication transmission timeout
- A006 Parameter copy error
- A007 Parameter copy error
- A009 IGBT overheat warning
- A011 PID feedback signal warning
- A012 AI(ACI) current signal disconnected
- A013 Low current warning
- A017 Overspeed warning
- A019 Input phase loss
- A020 Over torque
- A022 Motor overheat
- A028 Output phase loss warning
- A036 CANopen software disconnected
- A037 CANopen software disconnected
- A039 CANopen hardware disconnected
- A040 CANopen index error
- A041 CANopen station number fault
- A042 CANopen memory error
- A044 CANopenSDO receive overflow
- A046 CANopen format error
- E001 Overcurrent during acceleration
- E002 Overcurrent during deceleration
- E003 Overcurrent at constant speed
- E004 Ground fault short circuit
- E006 Stop overcurrent
- E007 Overvoltage during acceleration
- E008 Overvoltage during deceleration
- E009 Overvoltage at constant speed
- E010 Stop overvoltage
- E011 Undervoltage during acceleration
- E012 Undervoltage during deceleration
- E013 Undervoltage at constant speed
- E014 Stop undervoltage
- E015 Input phase loss
- E016 IGBT overtemperature
- E021 Inverter overload
- E022 Motor 1 overload
- E023 Motor 2 overload
- E024 Motor overheat
- E026 Over torque 1
- E028 Low current
- E029 Reached limit
- E036 CC hardware circuit fault
- E037 OC hardware circuit fault
- E040 Motor auto-tuning fault
- E041 PID disconnected
- E042 PG feedback setting error
- E048 AI current signal disconnected
- E049 External fault
- E051 External interruption
- E052 Password entered wrong three times
- E055 Invalid communication address
- E056 Communication data error
- E057 Communication write to read-only address
- E058 Modbus transmission timeout
- E066 Software overcurrent
- E079 U phase overcurrent
- E080 V phase overcurrent
- E081 W phase overcurrent
- E082 Output phase U loss
- E083 Output phase V loss
- E084 Output phase W loss
- E087 Low-frequency overload
- E101 CANopen disconnected
- E102 CANopen disconnected
- E104 CANopen hardware disconnected
- E105 CANopen index error
- E106 CANopen station number fault
- E107 CANopen memory error
- E120 EMS overcurrent
- E134 Motor 3 overload
- E135 Motor 4 overload
- E142 No feedback current in motor auto-tuning
- E143 Motor auto-tuning motor phase loss
- Er00 Voice: elevator overload voice: sensor fault
- Er01 Inverter unit fault
- Er02 Hardware overcurrent
- Er03 Hardware overvoltage
- Er08 Acceleration overvoltage
- Er09 Deceleration overvoltage
- Er12 Undervoltage
- Er13 Drive overload
- Er15 Module overheat
- Er23 Input phase loss
- Er24 Output phase loss
- Er29 EEPROM storage error
- Er30 Encoder fault
- Er31 Brake current too large
- Er32 Brake signal fault
- Er33 Holding brake not and disconnected during operation
- Er34 Holding brake not and disconnected at stop
- Er35 Brake pad heavily worn
- Er36 Utility-frequency output contactor not closed
- Er47 Slave fault during multi-pump confluence
- Er48 CAN address conflict during multi-pump confluence
- Er90 Motor current did not reach brake-open current in time during run
- Er91 Set run frequency below brake-open frequency
- Er92 Motor auto-tuning failure
- Err01 Inverter module fault
- Err02 Overcurrent during acceleration
- Err03 Overcurrent during deceleration
- Err04 Overcurrent during acceleration
- Err05 Overcurrent during deceleration
- Err06 Constant speed overcurrent during operation
- Err07 Constant speed overvoltage during operation
- Err08 Overvoltage during acceleration
- Err09 Overvoltage during deceleration
- Err10 Constant speed overvoltage during operation
- Err12 Undervoltage
- Err13 Drive overload
- Err14 Motor overload
- Err15 Drive overheat
- Err16 Software overcurrent
- Err17 Current detection fault
- Err18 Current detection fault
- Err19 Motor tuning fault
- Err20 Ground fault
- Err21 Tuning timeout fault
- Err22 Encoder detection fault
- Err23 Input phase loss
- Err24 Output phase loss
- Err25 Parameter read/write error
- Err26 Run time reached
- Err27 Communication error
- Err28 External fault
- Err29 Excessive speed deviation
- Err30 User-defined fault 1
- Err31 User-defined fault 2
- Err32 PID feedback loss during operation
- Err33 Fast current limit
- Err34 Load loss fault
- Err35 Input power supply fault
- Err36 Function board communication error
- Err37 Parameter storage error
- Err39 Current run time reached
- Err40 Cumulative run time reached
- Err42 Motor switchover during run
- Err43 Motor overspeed
- Err44 DSP board communication error
- Err45 Magnetic pole position detection failed
- Err46 Master-slave control communication disconnected
- Err48 Bus communication error (telegram fault)
- Err49 Bus communication error (timeout error)
- Err50 Bus cycle address error
- Err51 Bus data out of range error
- Err52 Multi-pump confluence multi-master fault
- Err58 Parameter restore error
- Err59 Back-EMF tuning fault
- Err61 Braking transistor prolonged braking protection fault
- Err63 Reverse run time reached
- Err65 Pressure sensor voltage out of range
- Err66 Overspeed fault (runaway)
- oc Hardware circuit fault
- ov Hardware circuit fault