EURA Drives fault codes
Fault codes
- -E.r- Communication error
- AEr0 Outlet sensor open protection
- AEr1 Inlet sensor open protection
- AErr Analog disconnected
- AL-01 Overcurrent
- AL-02 Overvoltage
- AL-03 Undervoltage
- AL-04 Hardware fault
- AL-05 Electrical angle identification error
- AL-06 Overload
- AL-07 Overspeed
- AL-08 Drive overload
- AL-09 Excessive position control fault
- AL-10 Encoder fault
- AL-11 Emergency stop
- AL-12 Drive overheat
- AL-13 Main circuit power supply phase loss
- AL-14 Dynamic braking fault
- AL-16 Input terminal setting duplicate
- AL-17 Encoder open
- AL-18 Inertia identification error
- AL-19 Encoder battery warning
- AL-20 Servo motor E2ROM not initialization
- AL-21 Zero drift too large
- AL-22 Incremental encoder Z-phase signal missing
- AL-23 Torque mismatch too large
- AL-24 Encoder battery alarm
- AL-25 Motor overheat
- AL-26 Temperature disconnected
- AL-27 Overtravel
- AL-28 E2ROM fault
- AL-29 Leakage
- AL-30 Motor locked rotor
- AL-31 Full closed-loop hybrid deviation too large
- AL-32 Gantry sync fault
- AL-33 Electronic cam fault
- AL-34 PLC command error
- AL-35 Homing timeout
- AL-36 Parameter copy error
- AL-37 Network initialization failure
- AL-38 OP fault
- AL-39 Sync loss
- AL-40 Sync setting error
- AL-41 High configuration not detected
- AL-43 E-square protection
- AL-44 UVW encoder signal loss
- AL-45 Absolute encoder resolution fault
- AL-46 Absolute encoder overspeed
- AL-48 Mains power loss
- AL-49 Software overcurrent
- AL-51 PHY chip initialization fault
- AL-52 EtherCAT chip init fault
- AL-53 FPGA error reset
- AL-59 Motor runaway
- AL-61 STO activated for diagnosis
- AL-62 SR1/SR2 status mismatch
- AL-64 Drive mode fault
- AL05 Motor locked rotor
- AL07 Overspeed
- AL09 Position out of tolerance
- AL14 Dynamic braking unit fault
- AL28 EEPROM error
- AL35 Homing timeout
- AL41 High-impedance state not detected
- AL59 Motor runaway
- AdEr Current detection fault
- Aerr Open
- C.B. Contactor not closed
- CB Contactor closed fault
- CE Communication timeout error
- CE1 Panel disconnected
- Cb Contactor not closed
- ConE Bus disconnected
- E.L. Interference
- E.P. Water shortage protection
- ECHb CANopen open 2
- ECLG CANopen open 1
- EEEP EEPROM read/write error
- EP Underload signal
- EP2 Underload signal
- EP3 Underload signal
- EP4 Dry-run protection
- EP5 Inlet water shortage
- EP6 Water leakage protection
- ERR1 Password error
- ERR2 Parameter tuning failed
- ERR3 Overcurrent fault before run
- ERR4 Current zero point offset fault
- ESP External fault
- ESP1 Emergency stop
- Er0 Upper limit
- Er1 Water shortage stop
- Er2 Inverter fault
- Er3 Parameter error
- Er44 Slave station drop fault
- Er55 Load loss
- Er71 Copy timeout
- Er72 Copy while drive running
- Er73 Copy without opening password
- Er74 Copy between different models
- Er75 Copy prohibited
- Er86 Neutral-point voltage imbalance too large
- Er93 Dump overcurrent
- ErAT Pump auto-tuning fault
- ErJA Pump stall fault
- ErP External device fault
- ErT0 Time period parameter setting error
- Err User password error/severe external interference
- Err0 Changing function codes during run prohibited
- Err1 Password error
- Err2 Parameter measurement error
- Err3 Current fault before run
- Err4 Current zero point offset fault
- Err5 PID parameter setting error
- Err6 Watchdog fault
- EtC EtherCATCRC checksum error
- EthC EtherCAT disconnected
- Ethd EtherCAT connection failure
- Etnt Network initialization failure
- FCL Fast current limit (FCL)
- FER1 Multi-step pressure value corresponding analog voltage error
- FER2 Multi-step pressure value setting error
- FER3 Multi-step flow value corresponding analog voltage error
- FER4 Multi-step flow value setting error
- FILL Pipe filling timeout fault
- FL Speed tracking fault
- GP Ground fault (no GP on single-phase)
- LU Undervoltage
- O.C. Overcurrent
- O.E. DC overvoltage
- O.H. Heatsink overheat
- O.L. Overload
- OC Overcurrent
- OC-1 U phase overcurrent
- OC-2 V phase overcurrent
- OC-3 W phase overcurrent
- OC1 Overcurrent OC1
- OC1/OC2 Overcurrent
- OC2 Overcurrent OC2
- OC3 Constant speed overcurrent
- OE DC overvoltage
- OE1 Acceleration overvoltage
- OE2 Deceleration overvoltage
- OE3 Constant speed overvoltage
- OH Inverter overheat
- OH-1 U phase overheat
- OH-2 V phase overheat
- OH-3 W phase overheat
- OH-4 Rectifier bridge overheat
- OH1 PTC overheat
- OH4 Motor overheat
- OH5 CPU overheat
- OL Overload protection indication
- OL1 Inverter overload
- OL2 Motor overload
- OVER Full-package indication
- P.F. Phase loss
- P.O. Undervoltage
- PC PC
- PCE PMSM loss of synchronism fault
- PCE1 Locked rotor
- PEr Phase loss
- PF Input phase loss
- PF0 Output phase loss
- PF1 Input phase loss
- PFO Output phase loss
- PG Encoder fault
- PGo Resolver fault
- PGo3 14-wire encoder UVW all high or all low
- PNC PN communication CRC error
- PNT PROFINET communication handshake failed
- PNd PN disconnected
- PO Power-down indication
- PP Pressure gauge fault
- PP-1 Pressure sensor fault
- PP-2 Oil-pump reverse-rotation fault
- SDOF SD power-on voltage point low
- SLP Sleep fault
- SLP1 Inlet sleep
- SSLP Solar sleep
- STO STO
- STO1 STO1
- Tro KTY84 disconnected
- brE1 Material break fault
- brr1 Motor 1 holding brake feedback fault
- brr2 Motor 2 holding brake feedback fault
- nP Pressure control protection
- nP1 Inlet overpressure
- oPEn OPEn fault
- rSt Forced reset prompt