Delixi fault codes
Fault codes
- Ar22.1 Homing return direction fault
- Ar72.0 Motor motor power cable open
- Ar75.0 Forward overtravel warning
- Ar76.0 Reverse overtravel warning
- E001 Inverter overcurrent during acceleration
- E002 Inverter overcurrent during deceleration
- E003 Inverter constant speed run overcurrent
- E004 Inverter overvoltage during acceleration
- E005 Inverter overvoltage during deceleration
- E006 Inverter constant speed run overvoltage
- E007 Undervoltage during operation alarm
- E008 Motor overload alarm
- E009 Inverter overload alarm
- E012 Output phase loss alarm
- E013 Inverter module heatsink overheat alarm
- E014 Rectifier module heatsink overheat alarm
- E015 External fault alarm
- E016 485 communication error alarm
- E017 Current detection circuit fault alarm
- E020 Closed-loop feedback loss alarm
- E021 Water pressure overpressure alarm
- E023 Water shortage alarm
- E028 Keypad parameter copy error alarm
- EEP EEPROM error
- EF External fault
- Er01.0 Hardware overcurrent 1
- Er01.1 Hardware overcurrent 2
- Er02.2 Software overcurrent during acceleration
- Er02.3 Hardware overcurrent 2 during acceleration
- Er03.0 Group F0 parameter error
- Er03.1 Group F1-F8 parameter error
- Er03.2 Address error during read/write after parameter count change
- Er03.3 Hardware overcurrent 2 during deceleration
- Er04.2 Overvoltage at constant speed
- Er05.2 Overvoltage during acceleration
- Er06.2 Overvoltage during deceleration
- Er08.1 Undervoltage
- Er09.1 Inverter single-phase current overload
- Er09.2 Inverter output current overload
- Er10.1 Motor overload
- Er11.1 Input phase loss hardware
- Er11.2 Input phase loss software
- Er11.3 Input phase loss R phase hardware
- Er11.4 Input phase loss S phase hardware
- Er11.5 Input phase loss T phase hardware
- Er11.6 Input two/three-phase loss hardware protection
- Er12.1 Normal during operation output phase loss
- Er12.2 Output phase loss during abnormal running
- Er12.3 Output phase loss at low output frequency
- Er12.4 Output phase loss at low feedback frequency
- Er12.6 Stator resistor identification output phase loss
- Er12.7 Output phase loss during synchronous motor pole position identification
- Er12.8 V or W phase output loss detected before running
- Er12.9 U phase or three-phase output loss detected before running
- Er14.1 Expansion card communication error
- Er14.2 Expansion card communication error
- Er14.3 Expansion card communication error
- Er15.1 IGBT temperature detection too high
- Er17.1 Power-on detection ground fault
- Er19.1 Motor load loss
- Er20.1 PID feedback loss
- Er21.1 User-defined fault 1
- Er22.1 User-defined fault 2
- Er23.0 Excessive position deviation
- Er23.1 Cumulative power-on time reached
- Er24.1 Cumulative run time reached
- Er25.0 Initial angle identification failed
- Er25.1 Initial angle identification single-turn reset error
- Er25.2 Single-turn reset function fault
- Er25.3 Multi-turn reset function fault
- Er25.7 Encoder fault: encoder error during asynchronous motor dynamic identification
- Er27.1 Motor overheat
- Er28.0 Regenerative braking overload
- Er28.1 Excessive speed deviation
- Er29.1 Motor overspeed
- Er30.1 Initial position fault
- Er31.1 U phase current fault
- Er31.2 V phase current fault
- Er34.1 U phase fast current limit timeout
- Er34.2 V phase fast current limit timeout
- Er34.3 W phase fast current limit timeout
- Er38.1 Output short circuit overcurrent hardware interruption
- Er38.2 Output short circuit fault
- Er38.3 Output short circuit fault
- Er38.5 Output short circuit during pre-run phase loss detection
- Er38.6 Output short circuit during pre-run phase loss detection
- Er39.1 Zero drift detection braking transistor short circuit
- Er39.2 Braking transistor short circuit while not enabled
- Er39.3 Braking transistor short circuit
- Er40.1 Soft-charge resistor overload
- Er42.1 Logic error 1 during synchronous motor pole position identification
- Er42.2 Logic error 2 during synchronous motor pole position identification
- Er43.1 Phase sequence error in mains/inverter switchover
- Er44.2 Motor type inconsistent with parameter identification setting
- Er45.1 Over torque fault
- Er46.1 Locked rotor
- Er47.1 Local RS485 communication error
- Er47.2 Local RS485 communication error
- Er48.1 Ethernet port communication error
- Er48.2 Ethernet port communication error
- Er49.1 Type-C communication error
- Er49.2 Type-C communication error
- Er5 Internal circuit fault
- Er6 Motor rated current setting value too large
- Er91.0 Serial encoder motor overheat
- Er93.0 Serial encoder motor parameter check error
- Er95.0 Serial encoder multi-turn fault
- Er96.0 Serial encoder battery replacement warning
- Er97.0 Encoder battery failure and multiturn count lost
- Er98.0 Serial encoder overheat
- Er99.0 Serial encoder open
- Er99.1 Serial encoder communication timeout
- ErP Parameter setting error
- Err-0 Input phase loss
- Err-01 Constant speed overcurrent
- Err-02 Acceleration overcurrent
- Err-03 Deceleration overcurrent
- Err-04 Constant speed overvoltage
- Err-05 Acceleration overvoltage
- Err-06 Deceleration overvoltage
- Err-08 Undervoltage
- Err-09 Inverter overload
- Err-1 Overheat
- Err-10 Motor overload
- Err-12 Output phase loss
- Err-15 Inverter overheat
- Err-17 Motor ground fault
- Err-2 Soft starter overload
- Err-21 User-defined fault 1
- Err-28 Excessive speed deviation
- Err-3 Light load
- Err-36 24V power supply fault
- Err-38 Load short circuit fault
- Err-4 Three-phase imbalance
- Err-41 Input phase loss
- Err-42 Anti-fall safety device tripped
- Err-43 Main contactor feedback fault
- Err-44 Holding brake contactor feedback fault
- Err-45 Control board terminal fault
- Err-46 Control board communication error
- Err-47 Keypad connection fault
- Err-48 System power-on parameter error
- Err-49 Encoder feedback fault
- Err-5 Emergency stop
- Err-50 Pin sensor fault
- Err-6 Overcurrent (locked rotor)
- Err-7 Control board fault
- Err-8 Start time too long
- Err-9 Parameter read/write error
- Err01 Overcurrent at constant speed
- Err01.0 Hardware overcurrent
- Err01.1 Hardware overcurrent
- Err02 Overcurrent during acceleration
- Err03 Overcurrent during deceleration
- Err03.0 Group F0 parameter error
- Err03.2 Address error during read/write after parameter count change
- Err03.9 Function code attribute initialization error
- Err04 Overvoltage at constant speed
- Err05 Overvoltage during acceleration
- Err06 Overvoltage during deceleration
- Err06.0 Current sampling : zero drift fault
- Err06.1 Current sampling : circuit fault
- Err06.2 Current sampling: U/V phase balance fault
- Err07 Module fault
- Err08 Undervoltage
- Err09 Inverter overload
- Err09.0 Storage fault
- Err10 Motor overload
- Err10.0 Analog input zero drift too large
- Err10.1 Analog input voltage too large
- Err11 Input phase loss
- Err11.0 Drive undervoltage
- Err12 Output phase loss
- Err12.0 Drive overvoltage
- Err13 External fault
- Err13.0 Motor overspeed
- Err14 Communication error
- Err15 Inverter overheat
- Err15.0 Motor overload
- Err15.1 Motor locked rotor
- Err16 Inverter hardware fault
- Err17 Motor ground fault
- Err17.1 Input phase loss warning
- Err18 Motor identification error
- Err19 Motor load loss
- Err20 PID feedback loss
- Err20.1 Motor phase sequence error
- Err21 User-defined fault 1
- Err21.1 Drive overheat
- Err21.2 Braking transistor overtemperature warning
- Err22 User-defined fault 2
- Err22.0 Homing timeout
- Err22.1 Homing direction fault
- Err23 Cumulative power-on time reached
- Err23.0 Position out of tolerance
- Err24 Cumulative run time reached
- Err25 Encoder fault
- Err25.0 Initial angle identification failed
- Err25.1 Initial angle identification single-turn reset error
- Err25.2 Single-turn reset function fault
- Err25.3 Multi-turn reset function fault
- Err26 Parameter read/write error
- Err27 Motor overheat
- Err28 Excessive speed deviation
- Err28.0 Braking overload
- Err29 Motor overspeed
- Err30 Initial position fault
- Err30.0 Parameter save frequency exceeded
- Err31 Current detection fault
- Err32 Contactor fault
- Err33 Current detection fault
- Err34 Fast current limit timeout
- Err35 Motor switchover during operation
- Err36 24V power supply fault
- Err37.0 Internal position run fault
- Err39.0 Communication address conflict
- Err40 Soft-charge resistor fault
- Err64.0 DI function duplicate assignment warning
- Err66.0 Runaway fault
- Err70.0 External DI emergency stop fault
- Err71.0 External braking resistor too small warning
- Err72.0 Motor power cable open
- Err75.0 Forward overtravel warning
- Err76.0 Reverse overtravel warning
- Err91.0 Serial encoder motor overheat
- Err93.0 Serial encoder motor parameter check error
- Err95.0 Serial encoder multi-turn fault
- Err96.0 Serial encoder battery replacement warning
- Err97.0 Serial encoder low voltage warning
- Err98.0 Serial encoder overheat
- Err99.0 Serial encoder open
- Err99.1 Serial encoder communication timeout
- Grd Ground fault
- LL Under load
- Lo2 V2(I2) signal loss
- Lo3 Option VX signal loss
- LoF VF(IF) signal loss
- OC Overcurrent
- OV Overvoltage
- PUV Main circuit voltage insufficient
- SPi Busbar voltage fluctuation too large
- SPo Output phase loss
- cE RS-485 communication error
- d.Err Parameter error
- oCP Load short circuit fault
- oL Motor overload
- oL2 Inverter overload
- oL3 Over torque detection fault
- oPr1 Keypad communication error
- oh Heatsink overheat
- oht Heatsink overheat