Berges fault codes
Fault codes
- 0 Local stop
- 01 Watchdog trip
- 02 Power bridge identification error
- 03 Current calibration fault
- 04 TSP 24V power supply fault
- 05 DC voltage calibration fault (fault)
- 06 IOC trip
- 07 External fault/warning (fault)
- 09 Inter-processor communication error
- 1 Min. net voltage
- 10 UndervoltageDC-L DC Bus voltage to low
- 11 Option
- 12 Auto-Stop
- 13 SIO-Timeout
- 14 Position sensor
- 15 I²t-Watch
- 16 Overtemperature
- 17 MOL contact
- 18 Dyn.brake 80%
- 19 Motor synchron.
- 1Ph Overload 33 1Ph Overload
- 2 Overtemperature
- 20 Motor overload
- 21 I²t
- 22 R1-Measuring
- 23 Overcurrent
- 24 TSP 10V reference error
- 25 Cable cap.
- 26 Xs-Measuring
- 27 Set disconn
- 28 Sensor off.
- 29 Zero pulse
- 3 Overcurrent
- 30 CAN-Controller
- 31 Min. excitation
- 32 Watchdog reset
- 33 Ill.trap number
- 34 Ill.Ext.Bus Acc.
- 35 Ill.Instr.Access
- 36 Ill.Word Op.Acc.
- 37 Protection Fault
- 38 Undefined Opcode Undefined op-code
- 39 Stack Underflow
- 4 Error PWM
- 40 Stack Overflow
- 41 Nonmaskable Int.
- 42 Serial link timeout (fault)
- 43 Digital input logic not set
- 44 Digital input logic changed
- 45 Braking resistor overheat (fault)
- 46 Braking resistor overheat (warning)
- 47 Braking resistor overload (fault)
- 48 Braking resistor overload (warning)
- 5 MOL contact open
- 50 Fan fault
- 51 Fan warning
- 52 Motor overheat (warning)
- 53 Motor locked rotor (warning)
- 54 Motor underload (warning)
- 55 Communication timeout (fault)
- 56 Communication timeout (warning)
- 57 Network external error
- 58 Serial link timeout (warning)
- 59 Regeneration timeout
- 6 Overvoltage DC-L
- 60 DC voltage calibration (warning)
- 7 DC-Link failure
- 8 Speed observer
- 9 Dyn.brake-overld
- Br_LIMIT Moc przy hamowaniu dynamicznym osiągnęła granicy zaprogramowanej.
- Brk Wire 23 Brk Wire
- Comm Loss 25 Comm Loss
- Curr Calibr 3 Curr Calibr
- Drive TOL 28 Drive TOL
- Dyn Brake 15 Dyn Brake
- E-trip External fault
- EE Checksum 2 EE Checksum
- EE-F EEPROM error
- ERROR 1 Błąd w danych
- ERROR 2 Niezgodność oprogramowania i urządzenia.
- ERROR 3 Usterka procesora centralnego
- ERROR 4 Usterka klawiatury
- ERROR 5 Usterka pamięci stałej
- ERROR 6 Usterka działania schematu sygnałowego
- ERROR 7 Błąd sygnału taktującego
- ERROR 8 Błąd programu
- ERROR 9 Naruszenie działania kaskady wyjściowego
- F01 Computer Malfunction
- F02 Parameter Block Fault
- F03 Bus Current Measurement
- F04 Power Supply Overload
- F05 No DC Bus Voltage
- F06 Output Short Circuit
- F07 External Fault Mechanism
- F08 Option board fault
- F09 Loss of Communication with
- F10 Auto-Restart (68-NRST)
- F11 Ground Fault
- F12 External interference
- F13 Overvoltage on DC Bus
- F14 Undervoltage
- F15 DB Overload
- F16 Acceleration Overcurrent
- F17 Deceleration Overcurrent
- F18 Running Overcurrent
- F19 Heat sink Over Tempera-
- F20 Timed Overload
- Ground 11 Ground
- I<4mA Reference signal <4 mA
- ILIMIT Current limit
- IOC Trip 6 IOC Trip
- Keypad Loss 24 Keypad Loss
- Low Temp 21 Low Temp
- Low Voltage 32 Low Voltage
- MOL Motor overload (MOL input)
- Model ID 8 Model ID
- Motor TOL 20 Motor TOL
- O-Uolt DC bus overvoltage
- O-l Output overcurrent/motor overload
- O-t Heatsink overheat
- OL-br Braking resistor overload
- OT_MOTOR Motor overheat
- OVERLOAD Overload
- OVERTEMP Zanadto wysoka temperatura inwertora (chłodnicy).
- OVERVOLT Overvoltage
- Ol-b Braking resistor short circuit
- Over Temp 19 Over Temp
- OverCurrent 18 OverCurrent
- OverVoltage 13 OverVoltage
- P-LOS Power supply phase loss
- P-LOSS Power supply phase loss
- PS-Trp Power stage fault
- Param Range 30 Param Range
- Power Supp 4 Power Supp
- Pwr Bridge 27 Pwr Bridge
- Pwr Wiring 31 Pwr Wiring
- RS Meas. Fail 34 RS Meas. Fail
- Ref Loss 22 Ref Loss
- Regen Time 26 Regen Time
- Res Lockout 10 Res Lockout
- SC-trP SC-trP Błąd komunikacji szeregowej
- Stuck Key 29 Stuck Key
- System 1 System
- U-Uolt DC bus undervoltage
- UNDERVOL Undervoltage
- Vac Imblnce 12 Vac Imblnce
- lin-F Analog current signal fault
- th-Flt Heatsink thermistor fault